Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as to when a switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM


E147417E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

1.INSPECT RADIO RECEIVER


    E141020E11
  1. Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-7 (SW1) - E3-6 (SWG)
    No switch is pushed
    Approx. 100 kΩ
    E3-7 (SW1) - E3-6 (SWG)
    SEEK+ switch: push
    0 to 2.5 Ω
    E3-7 (SW1) - E3-6 (SWG)
    SEEK- switch: push
    Approx. 0.3 kΩ
    E3-7 (SW1) - E3-6 (SWG)
    VOL+ switch: push
    Approx. 1 kΩ
    E3-7 (SW1) - E3-6 (SWG)
    VOL- switch: push
    Approx. 3.1 kΩ
    E3-8 (SW2) - E3-6 (SWG)
    No switch is pushed
    Approx. 100 kΩ
    E3-8 (SW2) - E3-6 (SWG)
    MODE switch: push
    0 to 2.5 Ω
    E3-8 (SW2) - E3-6 (SWG)
    ON HOOK switch: push (*1)
    Approx. 0.3 kΩ
    E3-8 (SW2) - E3-6 (SWG)
    OFF HOOK switch: push (*1)
    Approx. 1 kΩ

    *1: for Premium models



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.



  1. Measure the resistance according to the values in the table below.


    E152197E02


    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    z2-10 (AU1) - z2-8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    SEEK+ switch: push
    0 to 2.5 Ω
    z2-10 (AU1) - z2-8 (EAU)
    SEEK- switch: push
    Approx. 0.3 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    VOL+ switch: push
    Approx. 1 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    VOL- switch: push
    Approx. 3.1 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    MODE switch: push
    0 to 2.5 Ω
    z2-9 (AU2) - z2-8 (EAU)
    ON HOOK switch: push (*1)
    Approx. 0.3 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    OFF HOOK switch: push (*1)
    Approx. 1 kΩ

    *1: for Premium models



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3.INSPECT SPIRAL CABLE


    I039337E87
  1. Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    z2-8 (EAU) - D16-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-10 (AU1) - D16-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-9 (AU2) - D16-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

    HINT:
    1. REMOVAL (Click here)
    2. INSTALLATION (Click here)



NG
REPLACE SPIRAL CABLE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)