Home › TRANSMISSION · U151E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0793    Intermediate Shaft Speed Sensor "A"

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the counter gear. By comparing the counter gear speed signal (NC) with the direct clutch speed sensor signal (NT), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. Thus smooth gear shifting is performed.

DTC No.
DTC Detection Condition
Trouble Area
P0793
ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic)
  1. (a) Vehicle speed: 50 km/h (31 mph) or more
  2. (b) Park/neutral position switch (NSW (STAR)) is OFF
  3. (c) Speed sensor (NC): less than 300 rpm
  1. Open or short in transmission revolution sensor NC (speed sensor NC) circuit
  2. Transmission revolution sensor NC (speed sensor NC)
  3. ECM
Reference (Using an oscilloscope):
Check the waveform between terminals NC+ and NC- of the ECM connector.
C093866E09
Standard: Refer to the illustration. 
Terminal
NC+ - NC-
Tool setting
1 V/DIV, 1ms/DIV
Vehicle condition
Vehicle speed 30 km/h (19 mph): (3rd gear)
Engine speed 1400 rpm

MONITOR DESCRIPTION

The NC terminal of the ECM detects a revolution signal from the speed sensor (NC) (counter gear rpm). The ECM calculates a gearshift comparing the speed sensor (NT) with the speed sensor (NC).
While the vehicle is operating in 2nd, 3rd, 4th or 5th gear in the shift position of D, if the counter gear revolution is less than 300 rpm *1although the output shaft revolution is more than 1,000 rpm *2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0793: Speed sensor (NC)/Verify pulse input
Required sensors/Components
Speed sensor (NC), Speed sensor (NT), Park/neutral position switch
Frequency of operation
Continuous
Duration
5 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
P0500 (VSS)
P0748, P0778, P0798 (Shift solenoid valve(range))
Engine
Running
NSW (STAR) switch
OFF
Output shaft rpm
1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Sensor signal rpm
Less than 300 rpm

COMPONENT OPERATING RANGE


Counter gear speed sensor (NC)

HINT:
3rd when shift lever position is D position (After warming up the engine):
  1. Intermediate shaft speed (NC) becomes close to the engine speed.


WIRING DIAGRAM


G031763E86


INSPECTION PROCEDURE

HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


READ DATA LIST
  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Techstream to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn on the tester.

  6. Select the item "Powertrain / Engine and ECT / Data List".

  7. According to the display on the tester, read the "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NC)
    Counter Gear Speed/
    display: 50 r/min

    HINT:
    3rd when shift lever position is D position (After warming up the engine):
    1. Intermediate shaft speed (NC) becomes close to the engine speed.

    -

    HINT:
    1. SPD (NC) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR INSTALLATION


    BR03795E35
  1. Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.



NG
REPLACE SPEED SENSOR (NC) (Click here)
OK


2.INSPECT SPEED SENSOR (NC)


    C110343E71
  1. Disconnect the speed sensor connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (NC) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM)


    C168530E26
  1. Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B2-34 (NC+) - B2-26 (NC-)
    20°C (68°F)
    560 to 680 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B2-34 (NC+) - Body ground
    Always
    10 kΩ or higher
    B2-26 (NC-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)