DTC P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0776 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0776: Shift solenoid valve SL2/OFF malfunction Shift solenoid valve SL2/ON malfunction |
| Required sensors/Components | Shift solenoid valve SL2, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) 1.8 sec. OFF malfunction (B) and (C) 0.8 sec. ON malfunction (A) and (B) 0.8 sec. ON malfunction (C) 0.4 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) | P0712, P0713 (ATF temperature sensor circuit) P0115, P0117, P0118 (ECT sensor circuit) P0717 (Turbine speed sensor circuit) P0793 (Intermediate shaft speed sensor circuit) P0500 (Vehicle speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P2769, P2770 (Shift solenoid valve DSL circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0505, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (Electronic throttle system (if applicable)) |
| ECT (Engine coolant temperature) | 10°C (50°F) or more |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -20°C (-4°F) or more |
| ECM lock-up command | OFF |
| Vehicle speed | 3rd Less than 60 km/h (37 mph) |
| 4th, 5th Less than 120 km/h (75 mph) | |
| Throttle valve opening angle | 7% or more |
| ECM selected gear | 1st |
| Vehicle speed | Less than 40 km/h (25 mph) |
| Throttle valve opening angle | 4.5% or more at engine speed 1900 rpm (Varies with engine speed) |
| ECM selected gear | 3rd |
| Throttle valve opening angle | 4.5% or more at engine speed 1900 rpm (Varies with engine speed) |
| Duration time from shift command of ECM | 15 sec. or more |
| ECM selected gear | 4th or 5th |
| ECM selected gear | 1st |
| Vehicle speed | Less than 40 km/h (25 mph) |
| Throttle valve opening angle | 4.5% or more at engine speed 1900 rpm (Varies with engine speed) |
| ECM selected gear | 3rd |
| Throttle valve opening angle | 5% or more at output speed 1400 rpm (Varies with engine speed) |
| Malfunction of pressure control solenoid "B" (SL2) and "C" (SL3) | Not detected |
| Throttle valve opening angle | 7.0% or more at output speed 1050 rpm (Varies with engine speed) |
| Malfunction of pressure control solenoid "B" (SL2) | Not detected |
| Difference between engine speed and input (turbine) speed | Less than 35 rpm |
| Input (turbine) speed/Intermediate shaft speed | 0.93 to 1.07 |
| Input (turbine) speed/Intermediate shaft speed | 0.64 to 0.74 |
| Input (turbine) speed/Intermediate shaft speed | 2.72 to 2.86 |
| Input (turbine) speed - Intermediate shaft speed | 700 rpm or more |
| Input (turbine) speed - Intermediate shaft speed | Less than -500 rpm or 700 rpm or more |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Powertrain / Engine and ECT / Active Test / Shift Status".
According to the display on the tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set each shift position by yourself. [Vehicle Condition]
| 1st/2nd/3rd/4th/5th | Possible to check the operation of the shift solenoid valves. |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0776) |
Connect Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the Techstream main switch ON.
When you use Techstream:
Select the item "Powertrain / Engine and ECT / Trouble Codes".
Read the DTCs using Techstream.
| Result | Proceed to |
| P0776 | A |
| P0776 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE (SL2) |
![]() |
Remove the shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
|
| ||||
| OK | ||
| ||