Home › TRANSMISSION · U151E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0741    Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve DSL)

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, intermediate (counter) shaft speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect a mechanical problems of the shift solenoid valve DSL, valve body and torque converter clutch.

DTC No.
DTC Detection Condition
Trouble Area
P0741
Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock up remains ON in the lock-up OFF range.
(2-trip detection logic)
  1. Shift solenoid valve DSL remains open or closed
  2. Valve body is blocked
  3. Torque converter clutch
  4. Automatic transaxle (clutch, brake or gear etc.)
  5. Line pressure is too low

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the speed sensor (NT), speed sensor (NC), engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input turbine rpm (NT). The ECM calculates the actual transmission gear by comparing input turbine rpm (NT) to counter gear rpm (NC). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to the shift solenoid DSL. When the shift solenoid DSL is turned on, it applies pressure to the lock-up relay valve and locks the torque converter clutch.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in the shift solenoid valve DSL or lock-up system performance. The ECM will turn on the MIL and store the DTC.

HINT:
Example:
When any of the following is met, the system judges it as a malfunction.

  1. There is a difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.
    (Engine speed is at least 75 rpm greater than input turbine speed.)
  2. There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up off.
    (The difference between engine speed and input turbine speed is less than 35 rpm.)

MONITOR STRATEGY


Related DTCs
P0741:
Shift solenoid valve DSL/OFF malfunction
Shift solenoid valve DSL/ON malfunction
Required sensors/Components
Shift solenoid valve DSL, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE), Throttle position sensor (VPA1), Mass air flow sensor (MAF), Transmission temperature sensor (THO1), Engine coolant temperature sensor (ECT)
Frequency of operation
Continuous
Duration
OFF malfunction (A)
Continuous.
OFF malfunction (B)
1 sec.
OFF malfunction (C)
3.5 sec.
ON malfunction
1.8 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever this DTC is not present.
(Not circuit malfunction)
P0712, P0713 (ATF temperature sensor circuit)
P0115, P0117, P0118 (ECT sensor circuit)
P0717 (Turbine speed sensor circuit)
P0793 (Intermediate shaft speed sensor circuit)
P0500 (Vehicle speed sensor circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0798 (Shift solenoid valve SL3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P2769, P2770 (Shift solenoid valve DSL circuit)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0505, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (Electronic throttle system (if applicable))
ECT (Engine coolant temperature)
10°C (50°F) or more
Transmission range
"D"
TFT (Transmission fluid temperature)
-20°C (-4°F) or more

OFF malfunction (A): 
ECM selected gear
3rd
Throttle valve opening angle
4.5% or more at engine speed gear 1900 rpm (varies with engine speed)

OFF malfunction (B): 
ECM selected gear
5th
Vehicle speed
10 km/h (6 mph) or more

OFF malfunction (C): 
ECM lock-up command
ON
ECM selected gear
3rd, 4th or 5th
Vehicle speed
25 km/h (16 mph) or more

ON malfunction: 
ECM lock-up command
OFF
ECM selected gear
3rd, 4th or 5th
Throttle valve opening angle
7% or more
Vehicle speed
3rd
25 to 60 km/h (16 to 37 mph)
4th, 5th
25 to 120 km/h (16 to 75 mph)

TYPICAL MALFUNCTION THRESHOLDS


Either of the following conditions is met: OFF malfunction or ON malfunction OFF malfunction: 
Engine Speed - Input (turbine) speed
100 rpm or more

ON malfunction: 
Difference between engine speed and input (turbine) speed
Less than 35 rpm

INSPECTION PROCEDURE

HINT:
Using Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


PERFORM ACTIVE TEST
  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Techstream to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Select the item "Powertrain / Engine and ECT / Active Test".

  6. According to the display on the tester, perform the "Active Test".

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Lock Up
    [Test Details]
    Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35 %
    2. Vehicle Speed: 60 km/h (37 mph) or more
    ON/OFF
    Possible to check the DSL operation.

    HINT:
    1. This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.
    2. This test can be conducted in the 5th gear.



  7. Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

    HINT:
    1. When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
    2. Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)


    G029214E20

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0741)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the Techstream main switch ON.

  1. When you use Techstream:
    Select the item "Powertrain / Engine and ECT / Trouble Codes".

  1. Read the DTCs using Techstream.

    Result:

    Result
    Proceed to
    P0741
    A
    P0741 and other DTCs
    B

    HINT:
    If any other codes besides "P0741" are output, perform the troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT TRANSMISSION WIRE (DSL)


    C113969E59
  1. Disconnect the transmission wire connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    10 (DSL) - Body ground
    20°C (68°F)
    11 to 13 Ω



NG
Go to step 4
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    C168530E22
  1. Connect the transmission wire connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B2-11 (DSL) - Body ground
    20°C (68°F)
    11 to 13 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SHIFT SOLENOID VALVE (DSL)


    C113970E11
  1. Remove the shift solenoid valve DSL.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Solenoid Connector (DSL) - Solenoid Body (DSL)
    20°C (68°F)
    11 to 13 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid valve makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE (DSL) (Click here)
OK


5.CHECK TRANSMISSION WIRE

OK:
The connectors and pins are securely installed.
There is no open or short on the wire harness.



NG
REPAIR OR REPLACE TRANSMISSION WIRE (Click here)
OK


6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on each valve and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


7.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

OK:
The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR AUTOMATIC TRANSAXLE ASSEMBLY (Click here)