Home › TRANSMISSION ยท U151E AUTOMATIC TRANSAXLE › SPEED SENSOR

SPEED SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL SPEED SENSOR (NC SENSOR)


    C090570
  1. Coat a new O-ring with ATF.

  1. Install the speed sensor with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Make sure to install the same manufacturer's sensor.

  1. Connect the speed sensor connector.



2. INSTALL SPEED SENSOR (NT SENSOR)


    C090569
  1. Coat a new O-ring with ATF.

  1. Install the speed sensor with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Make sure to install the same manufacturer's sensor.

  1. Connect the speed sensor connector.



3. INSTALL AIR CLEANER BRACKET


    A171820
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }



4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A170450
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.



5. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A171941E01
  1. Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A170887
  1. Connect the 3 vacuum hoses.



    A171944
  1. Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.



7. INSTALL NO. 1 AIR CLEANER INLET


    A170454E01
  1. Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.



8. INSTALL NO. 2 AIR CLEANER INLET


    A170453
  1. Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.



9. INSTALL COOL AIR INTAKE DUCT SEAL


    A170196
  1. Install the cool air intake duct seal with the 11 clips.



10. INSTALL BATTERY


    A171858E01
  1. Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Install the positive battery terminal and nut.

  1. Connect the negative battery terminal, and tighten the nut.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).