Home › TRANSMISSION ยท U151E AUTOMATIC TRANSAXLE › VALVE BODY ASSEMBLY

VALVE BODY ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL MANUAL VALVE
  1. Install the manual valve to the valve body assembly.



2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    C050017
  1. Install the spring and check ball body.

  1. Align the groove of the manual valve with the pin of the lever.



    C091933E05
  1. Install the 17 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    1. Push the valve body against the accumulator piston springs and check ball body to install the valve body.
    2. First, temporarily tighten the bolts marked (1) in the illustration because they are positioning bolts.

    Bolt length:
    Bolt A:
    25 mm (0.98 in.)
    Bolt B:
    57 mm (2.24 in.)
    Bolt C:
    41 mm (1.61 in.)



3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    C091932
  1. Coat a new O-ring with ATF.

  1. Install the O-ring to the oil strainer.



    C091931
  1. Install the oil strainer with the 3 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



4. INSTALL TRANSMISSION WIRE


    C091927E08
  1. Coat a new O-ring with ATF.

  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }

  1. Connect the 7 shift solenoid valve connectors.



5. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    D030865E03
  1. Install the 2 magnets in the oil pan.

  1. Apply adhesive to the 18 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    C091925
  1. Install the oil pan and a new gasket to the transaxle case with the 18 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

    NOTICE:
    Apply adhesive to the bolts and tighten them within 10 minutes of application.



6. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

HINT:
(Click here)



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. ADD AUTOMATIC TRANSAXLE FLUID


9. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. Park the vehicle on a level surface and set the parking brake.



    D025120E05
  1. With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to S1 and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put the dipstick back all the way.

  1. Take out the dipstick again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
    If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
    If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.



10. INSPECT FOR TRANSAXLE FLUID LEAK


11. INSTALL NO. 2 ENGINE UNDER COVER


    A171854
  1. Install the No. 2 engine under cover with the 2 bolts.



12. INSTALL NO. 1 ENGINE UNDER COVER


    A171855
  1. Install the No. 1 engine under cover with the 6 bolts and 2 clips.



13. INSTALL ENGINE UNDER COVER ASSEMBLY


    A171850
  1. Install the engine under cover assembly with the 4 bolts and 5 clips.



    A171849
  1. Install the engine under cover assembly RR with the 2 bolts.



14. RESET MEMORY

HINT:
(Click here)