FRONT COOLING UNIT > INSTALLATION |
| 1. INSTALL AIR CONDITIONING UNIT |
Install the air conditioning unit with the 3 bolts.

| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/o PTC Heater) |
Driver Side:
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.
Passenger Side:
Using a 12 mm hexagon wrench, adjust the position of the 2 collars.
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.
Connect the connector.

Install the 2 bolts and 2 caps to the engine compartment side.
Install the instrument panel reinforcement assembly with air conditioning unit with the nut.
Engage the cooler drain hose.

Connect the blower motor connector.
Install the 2 nuts and bolt.
Connect each connector.
Connect the 2 earth wires with the 2 bolts <A>.
Engage each clamp.

| 3. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/ PTC Heater) |
Driver Side:
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.
Passenger Side:
Using a 12 mm hexagon wrench, adjust the position of the 2 collars.
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.
Connect the connector.

Install the 2 bolts and 2 caps to the engine compartment side.
Install the instrument panel reinforcement assembly with air conditioning unit with the nut.
Engage the cooler drain hose.

Connect the 2 quick heater connectors.
Connect the blower motor connector.
Install the 2 nuts and bolt.
Connect each connector.
Connect the 2 earth wires with the 2 bolts <A>.
Engage each clamp.

| 4. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the 3 nuts.
Install the 2 bolts.
Install the No. 1 instrument panel brace sub-assembly with the screw.
![]() |
Engage each clamp.
Connect the earth wire with the bolt.
| 5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
![]() |
Install the 3 nuts.
Install the bolt.
Install the No. 2 instrument panel brace sub-assembly with the screw.
![]() |
Engage each clamp.
Connect the earth wire with the bolt.
| 6. INSTALL CENTER HEATER TO REGISTER DUCT |
![]() |
Engage the 4 claws and install the center heater to register duct.
Engage the clamp.
| 7. INSTALL NO. 1 CONSOLE BOX DUCT (w/o Rear Air Conditioning System) |
![]() |
Install the clip and the No. 1 console box duct.
| 8. INSTALL REAR NO. 3 AIR DUCT |
![]() |
Engage the 2 claws and install the rear No. 3 air duct.
Install the clip.
![]() |
Engage the claw and install the floor carpet.
| 9. INSTALL REAR NO. 1 AIR DUCT |
![]() |
Engage the 2 claws and install the rear No. 1 air duct.
Install the clip.
Engage the clamp.
![]() |
Engage the claw and install the floor carpet.
| 10. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Install the air conditioning amplifier assembly with the 2 screws.
Connect each connector.
| 11. INSTALL CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Key System) |
![]() |
Install the certification ECU (smart key ECU assembly) with the 2 nuts.
Connect the connectors.
| 12. INSTALL POWER STEERING ECU ASSEMBLY |
![]() |
Install the power steering ECU assembly with the 3 nuts.
![]() |
Check that the connector lever is at the fully unlocked position before installation.
![]() |
Connect the 4 connectors to the power steering ECU assembly.
Lightly pull on the connector and check that the connector does not disconnect.
| 13. CONNECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
![]() |
Connect the instrument panel junction block assembly with the 3 nuts.
| 14. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Check that the 2 bushings are securely installed to the steering column assembly.
![]() |
Install the steering column assembly with the bolt and 2 nuts.
Connect the connectors and engage the wire harness clamps to the steering column assembly.
![]() |
Connect the connector to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
| 15. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.
![]() |
Install a new bolt.
![]() |
Install the steering intermediate shaft sub-assembly to the steering column hole shield.
![]() |
Tighten the bolt.
| 16. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY |
![]() |
Engage the 2 claws to install the No. 1 air duct sub-assembly.
| 17. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Install the DLC3 to the driver side knee airbag assembly with the 2 claws.
![]() |
Connect the driver side knee airbag connector and tire pressure warning reset switch connector to the driver side knee airbag assembly.
![]() |
Support the driver side knee airbag assembly with one hand as shown in the illustration.
![]() |
Temporarily install the driver side knee airbag assembly with the 2 hooks.
![]() |
Install the driver side knee airbag assembly with the 4 bolts.
| 18. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
![]() |
Install the brake pedal support sub-assembly with the 4 nuts.
![]() |
Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.
![]() |
Connect the brake pedal load sensing switch connector and engage the clamp.
| 19. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Apply lithium soap base glycol grease to the push rod pin.
Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.
| 20. INSTALL BRAKE PEDAL RETURN SPRING |
![]() |
Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.
| 21. INSTALL STOP LIGHT SWITCH ASSEMBLY |
![]() |
Temporarily install the stop light switch assembly with the stop light switch lock nut.
![]() |
Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).
Tighten the stop light switch lock nut.
![]() |
Connect the connector.
| 22. INSPECT AND ADJUST BRAKE PEDAL HEIGHT |
Check the brake pedal height.
![]() |
Turn back the carpet.
Measure the shortest distance between the brake pedal surface and tibia pad.
Adjust the brake pedal height.
Disconnect the stop light switch connector.
Remove the stop light switch assembly.
Loosen the push rod clevis lock nut.
Adjust the brake pedal height by turning the push rod.
Tighten the push rod clevis lock nut.
Install and adjust the stop light switch .
Connect the stop light switch connector.
| 23. INSPECT BRAKE PEDAL FREE PLAY |
![]() |
Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.
Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.
| 24. INSPECT BRAKE PEDAL RESERVE DISTANCE |
![]() |
Release the parking brake lever.
With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.
| 25. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Pole Antenna Type) |
Engage the 5 claws.
Install the 2 bolts <D> and nut <H>.
Install the 2 clips.

Engage each clamp.
Install the 2 passenger airbag bolts <A>.
Install the bolt <E>.
Connect each connector and install the instrument panel safety pad assembly.

| 26. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Glass Antenna Type) |
Engage the 5 claws.
Install the 2 bolts <D> and nut <H>.
Install the 2 clips.

Engage each clamp.
Install the 2 passenger airbag bolts <A>.
Connect each connector and install the instrument panel safety pad assembly.

| 27. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Connect the connector.
| 28. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
Connect the connector.
![]() |
Install the front No. 2 speaker assembly with the 2 bolts.
| 29. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.
| 30. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
Connect the connector.
![]() |
Install the front No. 2 speaker assembly with the 2 bolts.
| 31. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.
| 32. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish RH.
Engage the 3 guides and 2 clips, then install the front pillar garnish RH.
| 33. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| 34. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish LH.
Engage the 3 guides and 2 clips, then install the front pillar garnish LH.
| 35. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| 36. INSTALL ENGINE SWITCH (w/ Smart Key System) |
![]() |
Engage the 2 claws to install the switch.
Connect the switch connector.
| 37. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the claw and 2 guides.
Install the front No. 2 console box insert with the 3 screws <F> and clip.
| 38. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Engage the claw and 2 guides.
Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.
| 39. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System) |
![]() |
Engage the 6 claws.
![]() |
Install the console box assembly with the 4 bolts and 2 screws.
| 40. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System) |
![]() |
Engage the 6 claws.
Connect the connector.
![]() |
Install the console box assembly with the 4 bolts and 2 screws.
| 41. INSTALL LOWER REAR CONSOLE BOX |
Install the lower rear console box.
| 42. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System) |
![]() |
Install the No. 2 console box duct as shown in the illustration.
| 43. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.
| 44. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector and clamp.
![]() |
Engage the 4 claws and 3 clips.
Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.
| 45. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.
| 46. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 47. INSTALL FRONT DOOR SCUFF PLATE RH |
| 48. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System) |
![]() |
Connect the hood lock control cable assembly.
Connect each connector.
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 49. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Connect the hood lock control cable assembly.
Connect each connector and the aspirator duct.
![]() |
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 50. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the claw and clip, install the cowl side trim sub-assembly LH.
Install the clip.
| 51. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the guide and the 8 claws, and install the front door scuff plate LH.
| 52. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System) |
Connect each connector.
![]() |
Engage the 4 clips.
![]() |
Install the radio receiver assembly with bracket with the 4 bolts.
| 53. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) |
Connect each connector.
![]() |
Engage the 4 clips.
![]() |
Install the navigation receiver assembly with bracket with the 4 bolts.
| 54. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System) |
Connect the connector.
![]() |
Engage the 4 clips and install the heater control and accessory assembly.
| 55. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) |
Connect the connector.
![]() |
Engage the 4 clips and install the air conditioning control assembly.
| 56. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Key System) |
![]() |
Apply protective tape to the areas shown in the illustration.
Connect each connector.
Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
| 57. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Key System) |
![]() |
Apply protective tape to the areas shown in the illustration.
Connect each connector.
Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
| 58. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.
| 59. INSTALL COMBINATION METER ASSEMBLY |
Connect the connector.
![]() |
Install the combination meter assembly with the 4 screws.
| 60. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.
| 61. POSITION FRONT WHEELS STRAIGHT AHEAD |
| 62. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 63. INSTALL STEERING COLUMN COVER |
![]() |
Engage the claw to install the upper steering column cover.
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 2 screws.
| 64. ADJUST SPIRAL CABLE SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Rotate the spiral cable counterclockwise slowly by hand until it stops.
![]() |
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
| 65. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 66. INSPECT STEERING WHEEL CENTER POINT |
| 67. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Support the steering pad with one hand as shown in the illustration.
![]() |
Connect the 2 airbag connectors to the steering pad.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
![]() |
Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
| 68. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Install the lower No. 2 steering wheel cover with the claw.
| 69. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Install the lower No. 3 steering wheel cover with the claw.
| 70. INSTALL FRONT WHEEL LH |
| 71. CONNECT COOLER REFRIGERANT LIQUID PIPE A |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.
Install the O-ring on the cooler refrigerant liquid pipe A.
Install the cooler refrigerant liquid pipe A.
| 72. CONNECT NO. 1 COOLER REFRIGERANT SUCTION PIPE |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant suction pipe.
Install the O-ring on the No. 1 cooler refrigerant suction pipe.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 73. CONNECT HEATER INLET WATER HOSE |
![]() |
Install the heater inlet water hose and attach the clip.
| 74. CONNECT HEATER OUTLET WATER HOSE |
![]() |
Install the heater outlet water hose and attach the clip.
| 75. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.
![]() |
Engage the 4 clamps.
| 76. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
Connect the connector.
| 77. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal LH.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal RH.
| 78. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 79. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 80. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 81. INSPECT STEERING PAD |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 82. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).
| 83. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug from the water inlet housing.
![]() |
Loosen the air drain plug at the top of the radiator 3 or 4 turns.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Condition | Specified Condition |
| w/ Rear Heater | 11.0 liters (11.6 US qts, 9.7 Imp. qts) |
| w/o Rear Heater | 8.8 liters (9.3 US qts, 7.7 Imp. qts) |
| Condition | Specified Condition |
| w/ Rear Heater | 11.7 liters (12.4 US qts, 10.3 Imp. qts) |
| w/o Rear Heater | 9.5 liters (10.1 US qts, 8.4 Imp. qts) |
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 84. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 85. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 86. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 87. INSPECT FOR REFRIGERANT LEAK |
After recharging with refrigerant gas, inspect for refrigerant leak using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a gas leak detector, inspect for refrigerant leak from the refrigerant lines.
![]() |
Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.
If a gas leak is not detected from the drain hose, remove the blower motor from the cooling unit. Insert the gas leak detector into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.