FUEL SYSTEM > PRECAUTION |
| 1.DISCHARGE FUEL SYSTEM PRESSURE |
For work associated with removal of the FUEL PUMP relay:
Remove the relay block cover.
![]() |
Remove the FUEL PUMP relay.
Start the engine.
After the engine stops, turn the ignition switch off.
Crank the engine again. Check that the engine does not start.
Remove the fuel tank cap to discharge pressure from the fuel tank.
Disconnect the cable from the negative (-) battery terminal.
Install the FUEL PUMP relay.
Perform the following to disconnect the fuel pump connector:
Remove the rear No. 1 seat assembly (for LH side) (Click here).
Remove the rear No. 1 seat assembly (for RH side) (Click here).
![]() |
Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)
![]() |
Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)
![]() |
Remove the rear floor service hole cover.
Disconnect the fuel pump connector.
Start the engine.
After the engine stops, turn the ignition switch off.
Crank the engine again. Check that the engine does not start.
Remove the fuel tank cap to discharge pressure from the fuel tank.
Disconnect the cable from the negative (-) battery terminal.
![]() |
Reconnect the fuel pump connector.
Install the rear floor service hole cover.
![]() |
Install the front floor carpet and the 3 clips. (w/ rear No. 2 seat)
![]() |
Engage the 3 claws to install the front floor carpet. (w/o rear No. 2 seat)
Install the rear No. 1 seat assembly (for LH side) (Click here).
Install the rear No. 1 seat assembly (for RH side) (Click here).
| 2.PRECAUTIONS |
Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.
Do not smoke or work near fire when handling the fuel system.
Keep gasoline away from rubber or leather parts.
| 3.FUEL LINE |
When disconnecting a high pressure fuel line, a large amount of gasoline will spill out, so observe the following procedures:
Discharge fuel system pressure.
Disconnect the fuel pump tube .
Drain the fuel that remains in the fuel pump tube.
![]() |
To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.
Put a container under the connectors.
Observe these precautions when disconnecting the fuel tube connector.
![]() |
Remove the fuel pipe clamp.
Check whether there is any dirt in the pipe around the connector before disconnecting it and remove the dirt as necessary.
![]() |
Disconnect the connector from the pipe by hand.
If the connector and the pipe are stuck, push in and pull on the connector to release it. Pull the connector out of the pipe carefully.
Check that there is no dirt or other foreign objects on the sealing surface of the disconnected pipe. Clean the surfaces if necessary.
![]() |
Do not damage the disconnected pipe or connector. Prevent entry of foreign objects by covering them with a plastic bag.
![]() |
Observe the following precautions when connecting the fuel tube connectors (Quick Type A):
Check if there is any damage or foreign objects on the connecting parts of the pipes.
Line up the 2 parts of the pipes to be connected, and push them together until the connector makes a "click" sound. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
Check for fuel leaks.
![]() |
Observe the following precautions when disconnecting the fuel tube connector (Quick type B):
Before disconnecting the connector, clean off any dirt that may be present.
Pinch the tabs of the fuel tube retainer to disengage the 2 claws. Push the retainer down as shown in the illustration.
![]() |
If the connector and pipe are stuck, push and pull on the connector while holding the pipe by hand. Pull the 2 pipes apart to separate the connector.
Check if there is any dirt or other foreign objects on the sealing surfaces of the disconnected pipes. Clean the sealing surfaces if necessary.
![]() |
Do not damage the disconnected pipe or connector. Prevent entry of foreign objects by covering them with a plastic bag.
![]() |
Observe the following precautions when connecting the fuel tube connector (Quick Type B):
Line up the 2 parts of the pipes to be connected, and fully push the fuel tube connector and pipe together until they are fully seated. Next, push the retainer into the connector until its claws lock. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
Check for fuel leaks.
Observe the following precautions when handling a nylon tube:
| 4.INJECTOR |
![]() |
Install the injector to the delivery pipe and the lower intake manifold as shown in the illustration.
![]() |
Observe the following precautions when removing and installing the fuel injectors:
Never reuse an O-ring.
When placing a new O-ring on the injector, do not damage the O-ring.
Coat a new O-ring with spindle oil or gasoline before installing it.
| 5.FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE |
![]() |
Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube assembly with pump and gauge. Doing so will cause reassembly of the fuel suction tube assembly with pump and gauge to be impossible as the tube is welded to the plate.
| 6.INSPECT FOR FUEL LEAK |
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs .