DTC B1900/73 Short in Front Driver Side Pretensioner Squib Circuit |
DTC B1901/73 Open in Front Driver Side Pretensioner Squib Circuit |
DTC B1902/73 Short to GND in Front Driver Side Pretensioner Squib Circuit |
DTC B1903/73 Short to B+ in Front Driver Side Pretensioner Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1900/73 |
|
|
| B1901/73 |
|
|
| B1902/73 |
|
|
| B1903/73 |
|
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the front seat outer belt assembly LH and center airbag sensor assembly.
Disconnect the connectors from the front seat outer belt assembly LH and center airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the floor wire No. 2 connector (on the front seat outer belt assembly LH side) is not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT DRIVER SIDE PRETENSIONER SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connector to the center airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK FLOOR WIRE NO. 2 (FRONT DRIVER SIDE PRETENSIONER SQUIB CIRCUIT) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the floor wire No. 2 from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-1 (L+) - Body ground | Ignition switch on (IG) | Below 1 V |
| O4-2 (L-) - Body ground | Ignition switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-1 (L+) - O4-2 (L-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-1 (L+) - Body ground | Always | 1 MΩ or higher |
| O4-2 (L-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-1 (L+) - O4-2 (L-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front seat outer belt assembly LH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||