Home › ENGINE › 2GR-FE CHARGING › GENERATOR

GENERATOR > INSTALLATION

for Preparation Click here



1. INSTALL GENERATOR ASSEMBLY


    A170743
  1. Install the wire harness clamp stay with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A170150
  1. Connect the generator bracket with the wire harness clamp.



    A170146
  1. Install generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A170145
  1. Temporally install the 2 bolts.



    A170145
  1. Fully tighten the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A170144
  1. Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 3 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.



2. INSTALL V-RIBBED BELT


    A162386E01
  1. Install the V-ribbed belt.

  1. Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.

    SST
    09961-00950  



    A139509E01
  1. If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed tensioner assembly pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.



3. INSTALL NO. 2 OIL LEVEL DIPSTICK GUIDE
  1. Install a new O-ring to the No. 2 oil level dipstick guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Push in the No. 2 oil level dipstick guide end into the No. 1 oil level dipstick guide.



    A170143
  1. Install the No. 2 oil level dipstick guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



4. INSTALL RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR


    A169441
  1. Install the radiator assembly and fan assembly with motor.



5. INSTALL COOLER CONDENSER ASSEMBLY


    A169439
  1. Install the cooler condenser assembly with the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



6. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A169433
  1. Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    A169432
  1. Connect the low pitched horn and high pitched horn connectors.



7. INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    B174197
  1. Apply MP grease to the sliding areas of the lock.



    B174190
  1. Connect the hood lock control cable.



    B174189
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B174188
  1. Install the hood lock nut cap.



8. INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    B174198
  1. Apply MP grease to the sliding areas of the lock.



    B174194
  1. Connect the hood lock control cable.



    B174193
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B174192
  1. Install the hood lock nut cap.



    B174191
  1. Connect the connector.



9. INSTALL RADIATOR GRILLE


    B172748
  1. Engage the 4 guides and 6 claws, and install the radiator grille.



    B172746
  1. Install the 4 clips and 2 bolts.



10. CONNECT COOLING FAN ECU CONNECTOR


    A169436
  1. Connect the cooling fan ECU connector and attach the wire harness clamps to the fan shroud RH side.



    A169435
  1. Attach the wire harness clamps to the fan shroud LH side.



11. CONNECT OIL COOLER HOSE


    A169429
  1. Connect the oil cooler hoses to the radiator.



12. CONNECT NO. 2 RADIATOR HOSE


    A169428
  1. Connect the No. 2 radiator hose to the radiator.



13. CONNECT NO. 1 RADIATOR HOSE


    A169427
  1. Connect the No. 1 radiator hose to the radiator.



14. INSTALL NO. 1 AIR CLEANER INLET


    A170454E01
  1. Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.



15. INSTALL NO. 2 AIR CLEANER INLET


    A170453
  1. Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.



16. INSTALL BATTERY

NOTICE:
When reconnected the cable, some systems need to be initialized. (Click here).



    A175880E02
  1. Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }

  1. Connect the positive battery terminal, and tighten the nut.

    Torque:
    Nut B:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Connect the negative battery terminal, and tighten the nut.

    Torque:
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }



17. INSTALL COOL AIR INTAKE DUCT SEAL


    A170196
  1. Install the cool air intake duct seal with the 11 clips.



18. INSTALL FRONT FENDER APRON SEAL RH


    A171853
  1. Install the front fender apron seal RH with the 2 bolts and clip.



19. INSTALL FRONT FENDER LINER RH


    B174752
  1. Install the front fender liner RH with the 5 clips and 7 screws.



    B174750
  1. Install 2 new grommets.

  1. Using a 4 mm hexagon wrench, install the 2 screws.



    B174754
  1. Install the screw and pin hold clip.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



20. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side .



21. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.



    A169415E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    w/o Trailer Towing System 
    Condition
    Specified Condition
    w/ Rear Heater
    11.0 liters (11.6 US qts, 9.7 Imp. qts)
    w/o Rear Heater
    8.8 liters (9.3 US qts, 7.7 Imp. qts)
    w/ Trailer Towing System 
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



22. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A169405
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



23. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Click here.



24. INSPECT FOR OIL LEAK


25. INSTALL NO. 1 ENGINE UNDER COVER


    A171855
  1. Install the No. 1 engine under cover with the 6 bolts and 2 clips.



26. INSTALL ENGINE UNDER COVER ASSEMBLY


    A171850
  1. Install the engine under cover assembly with the 4 bolts and 5 clips.



    A171849
  1. Install the engine under cover assembly RR with the 2 bolts.



27. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



28. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.