Home › TRANSMISSION ยท U151F AUTOMATIC TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSTALLATION

for Preparation Click here



1. INSTALL SHIFT LEVER ASSEMBLY


    C168462E01
  1. Install the shift lever assembly with the 4 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    HINT:
    Tighten the nuts in the order of A, B, C and D.

    NOTICE:
    Be careful not to route the indicator light or shift lock system wiring between the shift lever assembly and the floor while installing the shift lever assembly.

  1. Install the No. 2 console box mounting bracket with the 2 screws.



    C168461
  1. Connect the 2 connectors to the shift lever assembly.



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C131879E01
  1. Rotate the transmission control cable nut counterclockwise and, while holding the nut in that position, press in the stopper.



    C132225E01
  1. Connect the outer part of the transmission control cable assembly to the shift lever retainer.

    NOTICE:
    After installation, check that the outer part of the cable lock is protruding beyond portion A-A as shown in the illustration.



    C135727E03
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.



    C195452
  1. Install the cable end to the shift control unit.

    NOTICE:
    1. Check that the lock piece is pulled up.
    2. Install the cable end all the way to the base of the pin.



    C194138E01
  1. Push the lock piece into the adjuster case.

    NOTICE:
    Firmly push in the lock piece until the slider locks.



3. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    C168445
  1. Install the shift lever knob sub-assembly.



4. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.



5. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B168373
  1. Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.



6. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    B173629
  1. Engage the 6 claws.



    B173628
  1. Install the console box assembly with the 4 bolts and 2 screws.



7. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    B175149
  1. Engage the 6 claws.

  1. Connect the connector.



    B181135
  1. Install the console box assembly with the 4 bolts and 2 screws.



8. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.



9. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    B173013
  1. Install the No. 2 console box duct as shown in the illustration.



10. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.



11. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.



    B168370
  1. Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.



12. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B173000
  1. Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.



13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



14. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    B168371
  1. Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    B173009
  1. Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.



    B173021
  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



17. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



18. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



19. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Key System)


    B184679E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



20. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Key System)


    B184681E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



22. ADJUST SHIFT LEVER POSITION


    C135725E04
  1. Move the shift lever to N.

  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.

  1. Push the lock piece into the adjuster case.

    NOTICE:
    Firmly push in the lock piece until the slider locks.

  1. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.



23. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P position to the R position with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N position to the D position and moves rearward when shifting to the R position. If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.