REAR SUSPENSION MEMBER (for 2WD) > INSTALLATION |
| 1. INSTALL STUD BOLT (for LH Side) |
![]() |
Install the stud bolt.
| 2. INSTALL STUD BOLT (for RH Side) |
| 3. INSTALL HOLE PLUG |
![]() |
Install the hole plugs to the rear suspension member sub-assembly.
| 4. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH |
![]() |
Temporarily install a new rear suspension member body mounting front cushion LH to the position shown in the illustration.
Using SST and a press, install the rear suspension member body mounting front cushion LH to the rear suspension member sub-assembly.

![]() |
While observing from the side, press in the rear suspension member body mounting front cushion LH until there is no clearance between the rear suspension member body mounting front cushion LH and the rear suspension member sub-assembly as shown in the illustration.
| 5. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH |
![]() |
Temporarily install a new rear suspension member body mounting front cushion RH to the position shown in the illustration.
Using SST and a press, install the rear suspension member body mounting front cushion RH to the rear suspension member sub-assembly.

![]() |
While observing from the side, press in the rear suspension member body mounting front cushion RH until there is no clearance between the rear suspension member body mounting front cushion RH and the rear suspension member sub-assembly as shown in the illustration.
| 6. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side) |
![]() |
Temporarily install a new rear suspension member body mounting rear cushion (LH side) to the position shown in the illustration.
Using SST and a press, install the rear suspension member body mounting rear cushion (LH side) to the rear suspension member sub-assembly.

![]() |
While observing from the side, press in the rear suspension member body mounting rear cushion (LH side) until there is no clearance between the rear suspension member body mounting rear cushion (LH side) and the rear suspension member sub-assembly as shown in the illustration.
| 7. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side) |
| 8. INSTALL REAR SUSPENSION MEMBER |
![]() |
Set the jack and wooden blocks below the vehicle as shown in the illustration.
![]() |
Set the rear suspension member onto the jack as shown in the illustration.
![]() |
Raise the rear suspension member with a jack.
Install the rear suspension member and the rear lower suspension member stopper LH and RH with the 4 nuts.

Install the rear suspension member and the rear lower suspension member stoppers with the 2 bolts.

| 9. INSTALL EXHAUST PIPE CLAMP BRACKET SUB-ASSEMBLY |
![]() |
Install the exhaust pipe clamp bracket sub-assembly with the 3 bolts.
![]() |
Install the exhaust pipe clamp to the exhaust pipe clamp bracket sub-assembly.
| 10. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH |
![]() |
Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member with the bolt.
Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and the nut.
| 11. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH |
| 12. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH |
![]() |
Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member with the bolt.
Temporarily install the rear No. 2 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and the nut.
| 13. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH |
| 14. STABILIZE SUSPENSION |
![]() |
Jack up the rear axle carrier, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm (inner side) is horizontally aligned with the center of the rear axle hub.
| 15. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH |
![]() |
Using SST and a socket wrench (19 mm), fully tighten the bolt.
![]() |
Fully tighten the bolt
| 16. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH |
| 17. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH |
![]() |
Fully tighten the bolts.
| 18. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH |
| 19. INSTALL REAR STABILIZER BAR |
![]() |
Install the rear stabilizer bar with the 4 bolts.
| 20. INSTALL REAR STABILIZER LINK ASSEMBLY LH |
![]() |
Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.
| 21. INSTALL REAR STABILIZER LINK ASSEMBLY RH |
| 22. INSTALL REAR WHEELS |
| 23. INSTALL SPARE WHEEL CARRIER LOCK COVER (w/ Cover) |
| 24. INSTALL SPARE TIRE |
| 25. INSTALL LOWER SPARE WHEEL CARRIER HINGE COVER (w/ Cover) |
| 26. INSTALL DECK TRIM SERVICE HOLE COVER |
| 27. INSTALL REAR MAT |
![]() |
Install the rear mat.
| 28. INSTALL TONNEAU COVER ASSEMBLY |
Install the tonneau cover assembly.
| 29. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 2 deck board sub-assembly.
| 30. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 3 deck board sub-assembly.
| 31. INSTALL DECK BOARD ASSEMBLY |
![]() |
Install the deck board sub-assembly.
| 32. INSPECT AND ADJUST REAR WHEEL ALIGNMENT |