Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet.
The sensor plate rotates as each tooth passes through the pickup coil, and a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
  1. No crankshaft position sensor signal to ECM while cranking (1 trip detection logic)
  2. No crankshaft position sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Sensor plate (crankshaft position sensor plate)
  4. ECM
P0339
Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have lapsed since starter signal switched from ON to OFF
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Sensor plate (crankshaft position sensor plate)
  4. ECM
Reference: Inspection using an oscilloscope
A196825E04

HINT:
  1. The correct waveform is shown in the illustration.
  2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.
    Item
    Content
    Terminals
    VV1+ - VV1-
    VV2+ - VV2-
    NE+ - NE-
    Equipment Settings
    5 V/DIV., 20 ms./DIV.
    Conditions
    Cranking or idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is set 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check during cranking
P0335: Crankshaft position sensor range check during engine running
Required Sensors / Components (Main)
Crankshaft position sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Continuous
Duration
3 times
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever these DTCs are not present
None

Crankshaft Position Sensor Range Check during Cranking P0335: 
Starter
OFF
Ignition switch
ON (IG)
Battery voltage
7 V or more
Minimum battery voltage while starter ON
Less than 11 V
Number of VVT sensor signal pulse
6 times
CMP sensor circuit fail (P0340, P0342, P0343)
Not detected

Crankshaft Position Sensor Range Check during Engine Running P0335: 
Engine speed
600 rpm or more
Starter
OFF
Time after starter from ON to OFF
3 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Crankshaft Position Sensor Range Check during Cranking P0335: 
Number of crankshaft position sensor signal pulse
132 or less, or 174 or more

Crankshaft Position Sensor Range Check during Engine Running P0335: 
Crankshaft position sensor signal
No signal

COMPONENT OPERATING RANGE


Crankshaft position sensor
  1. Crankshaft position sensor output voltage fluctuates while crankshaft is revolving
  2. 34 crankshaft position sensor signals per crankshaft revolution

WIRING DIAGRAM


A136097E08


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)


    A148718E06
  1. Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    1630 to 2740 Ω
    1 - 2
    Hot
    2065 to 3225 Ω

    HINT:
    Terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    A168207E03
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    B21-1 (NE+) - B3-21 (NE+)
    Always
    Below 1 Ω
    B21-2 (NE-) - B3-20 (NE-)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    B21-1 (NE+) or B3-21 (NE+) - Body ground
    Always
    10 kΩ or higher
    B21-2 (NE-) or B3-20 (NE-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the crankshaft position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
OK


3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)


    BR03795E54
  1. Check the crankshaft position sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


4.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Remove the crankshaft position sensor plate (Click here).

  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.

  1. Reinstall the crankshaft position sensor plate (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE (Click here)
OK

REPLACE ECM (Click here)