DTC P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 |
|
|
| P0342 P0347 | Output voltage of VVT sensor is 0.3 V or less for 4 seconds (1 trip detection logic) |
|
| P0343 P0348 | Output voltage of VVT sensor is 4.7 V or more for 4 seconds (1 trip detection logic) |
|
| P0345 |
|
|

| Item | Content |
| Terminals | NE+ - NE- VV1+ - VV1- VV2+ - VV2- |
| Equipment Settings | 5 V/DIV., 20 ms./DIV. |
| Conditions | Cranking or idling |
| Related DTCs | P0340: Camshaft position sensor (Bank 1) open/short P0340: Camshaft position sensor (Bank 1) range check (Chattering) P0342: Camshaft position sensor (Bank 1) range check (low voltage) P0343: Camshaft position sensor (Bank 1) range check (high voltage) P0345: VVT sensor (Bank 2) open/short P0345: VVT position sensor (Bank 2) range check (Chattering) P0347: VVT position sensor (Bank 2) range check (low voltage) P0348: VVT position sensor (Bank 2) range check (high voltage) |
| Required Sensors / Components (Main) | VVT position sensor (Bank 1 and 2) |
| Required Sensors / Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: P0340 (Camshaft position sensor range check), P0340, P0342, P0343 (Camshaft position sensor range check (Chattering, Low voltage, High voltage)) P0345, P0347, P0348 (VVT sensor range check (Chattering, Low voltage, High voltage)) 5 seconds: Others |
| MIL Operation | 2 driving cycles: P0340 (Camshaft position sensor range check) Immediate: Others |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Starter | ON and not starter ON again |
| Minimal battery voltage while starter ON | Less than 11 V |
| Engine RPM | 600 rpm or more |
| Starter | OFF |
| Starter | OFF |
| Ignition switch on (IG) and time after ignition switch is off to on | 2 seconds or more |
| Engine RPM | 600 rpm or more |
| Starter | OFF |
| Battery voltage | 8 V or more |
| Ignition switch | ON (IG) |
| Starter | OFF |
| Ignition switch on (IG) and time after ignition switch is off to on | 2 seconds or more |
| Battery voltage | 8 V or more |
| Camshaft position signal | No signal |
| Camshaft position and crankshaft position phase | Mis-aligned |
| Camshaft position voltage | Less than 0.3 V, or more than 4.7 V |
| Camshaft position voltage | Less than 0.3 V |
| Camshaft position voltage | More than 4.7 V |
| VVT sensor signal | No signal |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V, or more than 4.7 V |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |
| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the VVT sensor connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B43-3 (VC2) - Body ground | Ignition switch on (IG) | 4.5 to 5.0 V |
| Tester Connection | Switch Condition | Specified Condition |
| B42-3 (VC2) - Body ground | Ignition switch on (IG) | 4.5 to 5.0 V |
Reconnect the VVT sensor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
![]() |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B22-1 (VVR+) - B3-19 (VV1+) | Always | Below 1 Ω |
| B22-2 (VVR-) - B3-29 (VV1-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B23-1 (VVL+) - B3-18 (VV2+) | Always | Below 1 Ω |
| B23-2 (VVL-) - B3-28 (VV2-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B22-1 (VVR+) or B3-19 (VV1+) - Body ground | Always | 10 kΩ or higher |
| B22-2 (VVR-) or B3-29 (VV1-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B23-1 (VVL+) or B3-18 (VV2+) - Body ground | Always | 10 kΩ or higher |
| B23-2 (VVL-) or B3-28 (VV2-) - Body ground | Always | 10 kΩ or higher |
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR) |
![]() |
Check the VVT sensor installation condition.
|
| ||||
| OK | |
| 4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE) |
Check the teeth of the sensor plate.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR |
Replace the VVT sensor (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Clear the DTCs.
Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0340, P0342, P0343, P0345, P0347 or P0348 | B |
|
| ||||
| A | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
![]() |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B22-3 (VC) - B1-23 (VC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B23-3 (VC) - B1-23 (VC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B22-3 (VC) or B1-23 (VC) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B23-3 (VC) or B1-23 (VC) - Body ground | Always | 10 kΩ or higher |
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||