Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
This electrical throttle control system does not use a throttle cable.
The throttle position sensor is mounted on the throttle body, and detects the opening angle of the throttle valve. This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has two sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.


A019802E77


DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. ECM
P0122
Output voltage of VTA1 is 0.2 V or less for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
Output voltage of VTA1 is 4.535 V or more for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. ECM
P0222
Output voltage of VTA2 is 1.75 V or less for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V, for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) is met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. Throttle position sensor (built into throttle body)
  3. ECM

HINT:
  1. When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on the Techstream: Powertrain / Engine and ECT / Data List / ETCS / Throttle Sensor Position No. 1 and Throttle Sensor Position No. 2.
  2. Throttle Sensor Position No. 1 denotes the VTA1 signal (expressed in percentages), and Throttle Sensor Position No. 2 denotes the VTA2 signal (expressed in voltages).


Reference (Normal Condition) 
Tester Display
Accelerator Pedal Fully Released
Accelerator Pedal Fully Depressed
Throttle Sensor Position No. 1
0.5 to 1.1 V
3.3 to 4.9 V
Throttle Sensor Position No. 2
2.1 to 3.1 V
4.5 to 5.0 V

MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
  1. A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and sets a DTC.
  2. VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and sets a DTC.
  3. VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0120: Throttle position sensor 1 range check (Fluctuating)
P0122: Throttle position sensor 1 range check (Low voltage)
P0123: Throttle position sensor 1 range check (High voltage)
P0220: Throttle position sensor 2 range check (Fluctuating)
P0222: Throttle position sensor 2 range check (Low voltage)
P0223: Throttle position sensor 2 range check (High voltage)
P2135: Throttle position sensor range check (Correlation)
Required Sensors / Components (Main)
Throttle position sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Continuous
Duration
2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223 (Accelerator pedal ON)
0.5 seconds: P2135
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
Either of following conditions A or B met
-
A. Ignition switch on (IG)
0.012 seconds or more
B. Electronic throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P0120: 
VTA1 voltage
0.2 V or less, or 4.535 V or more

P0122: 
VTA1 voltage
0.2 V or less

P0123: 
VTA1 voltage
4.535 V or more

P0220: 
VTA2 voltage
1.75 V or less, or 4.8 V or more

P0222: 
VTA2 voltage
1.75 V or less

P0223: 
VTA2 voltage when VTA1 0.2 V to 2.02 V
4.8 V or more

P2135: 
Either of following conditions A or B is met:
-
Condition A
-
Difference between VTA1 and VTA2 voltages
0.02 V or less
Condition B
-
Both of the following conditions are met
(a) or (b)
(a) VTA1 voltage
0.2 V or less
(b) VTA2 voltage
1.75 V or less

COMPONENT OPERATING RANGE


VTA1 voltage
0.2 to 4.535 V
VTA2 voltage
1.75 to 4.8 V

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed slowly, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM


A085458E29


INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM (THROTTLE POS AND THROTTLE POS #2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Sensor Position No. 2.

  1. Check the values displayed on the tester.

    Result:

    When accelerator pedal released
    When accelerator pedal depressed
    Trouble Area
    Proceed to
    Throttle Sensor Position No. 1
    Throttle Sensor Position No. 2
    Throttle Sensor Position No. 1
    Throttle Sensor Position No. 2
    0 to 0.2 V
    Between 0 V and 0.2 V
    0 to 0.2 V
    Between 0 V and 0.2 V
    VC circuit open
    A
    4.5 to 5.0 V
    Between 4.5 V and 5.0 V
    4.5 to 5.0 V
    Between 4.5 V and 5.0 V
    E2 circuit open
    A
    0 to 0.2 V or 4.5 to 5.0 V
    Between 2.4 V and 3.4 V
    (Fail-safe)
    0 to 0.2 V or 4.5 to 5.0 V
    Between 2.4 V and 3.4 V
    (Fail-safe)
    VTA1 circuit open or ground short
    A
    0.7 to 1.3 V
    (Fail-safe)
    Between 0 V and 0.2 V, or 4.5 V and 5.0 V
    0.7 to 1.3 V
    (Fail-safe)
    Between 0 V and 0.2 V, or 4.5 V and 5.0 V
    VTA2 circuit open or ground short
    A
    0.5 to 1.1 V
    Between 2.1 V and 3.1 V
    3.2 to 4.8 V
    (Not fail-safe)
    Between 4.5 V and 5.0 V
    (Not fail-safe)
    Throttle position sensor circuit normal
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)


    A168201E02
  1. Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    B27-5 (VC) - B1-23 (VC)
    Always
    Below 1 Ω
    B27-6 (VTA) - B1-20 (VTA1)
    Always
    Below 1 Ω
    B27-4 (VTA2) - B1-19 (VTA2)
    Always
    Below 1 Ω
    B27-3 (E2) - B1-28 (E2)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    B27-5 (VC) or B1-23 (VC) - Body ground
    Always
    10 kΩ or higher
    B27-6 (VTA) or B1-20 (VTA1) - Body ground
    Always
    10 kΩ or higher
    B27-4 (VTA2) or B1-19 (VTA2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE POSITION SENSOR - ECM)
OK


3.INSPECT ECM (VC VOLTAGE)


    A168199E15
  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-23 (VC) - B1-28 (E2)
    Ignition switch on (IG)
    4.5 to 5.0 V



NG
REPLACE ECM (Click here)
OK


4.REPLACE THROTTLE BODY
  1. Replace the throttle body (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)