Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2120    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
This electronic throttle control system does not use a throttle cable.
The accelerator pedal position sensor is integrated with the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


A112620E10


DTC No.
DTC Detection Condition
Trouble Area
P2120
VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
  1. Accelerator pedal position sensor
  2. ECM
P2122
VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic)
  1. Accelerator pedal position sensor
  2. Open in VCP1 circuit
  3. Open or ground short in VPA circuit
  4. ECM
P2123
VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
  1. Accelerator pedal position sensor
  2. Open in EPA circuit
  3. ECM
P2125
VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
  1. Accelerator pedal position sensor
  2. ECM
P2127
VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic)
  1. Accelerator pedal position sensor
  2. Open in VCP2 circuit
  3. Open or ground short in VPA2 circuit
  4. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or more
(b) VPA is between 0.4 V and 3.45 V
  1. Accelerator pedal position sensor
  2. Open in EPA2 circuit
  3. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
  1. Short between VPA and VPA2 circuits
  2. Accelerator pedal position sensor
  3. ECM

HINT:
When any of these DTCs are set, check the accelerator pedal position sensor voltage by selecting the following menu items on the Techstream: Select the following menu items: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Areas
Accel Sensor Out No. 1 When accelerator pedal Released
Accel Sensor Out No. 2 When accelerator pedal Released
Accel Sensor Out No. 1 When accelerator pedal Depressed
Accel Sensor Out No. 2 When accelerator pedal Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 5.0 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.6 to 4.5 V
3.4 to 5.0 V

HINT:
Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When either of the voltage outputs of VPA or VPA2 deviates from the standard range, or the difference between the voltage outputs of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and sets a DTC.
Example:
  1. When the voltage output of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is set.
  2. If the malfunction is not repaired successfully, a DTC is set 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P2120: Accelerator pedal position sensor 1 range check (fluctuating)
P2122: Accelerator pedal position sensor 1 range check (low voltage)
P2123: Accelerator pedal position sensor 1 range check (high voltage)
P2125: Accelerator pedal position sensor 2 range check (fluctuating)
P2127: Accelerator pedal position sensor 2 range check (low voltage)
P2128: Accelerator pedal position sensor 2 range check (high voltage)
P2138: Accelerator pedal position sensor range check (correlation)
Required Sensors / Components (Main)
Accelerator pedal position sensor
Required Sensors / Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds: P2120, P2122, P2125 and P2127
2.0 seconds: P2123, P2128 and P2138
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
Throttle actuator power
ON
Ignition switch
ON (IG)

TYPICAL MALFUNCTION THRESHOLDS


P2120: 
Either of the following conditions is met
Condition A or B
A. VPA voltage when VPA2 is 0.04 V or more
0.4 V or less
B. VPA voltage
4.8 V or more

P2122: 
VPA voltage when VPA2 is 0.04 V or more
0.4 V or less

P2123: 
VPA voltage
4.8 V or more

P2125: 
Either of the following conditions is met
Condition A or B
A. VPA2 voltage when VPA is 0.04 V or more
1.2 V or less
B. VPA2 voltage when VPA is 0.4 to 3.45 V
4.8 V or more

P2127: 
VPA2 voltage when VPA is 0.04 V or more
1.2 V or less

P2128: 
VPA2 voltage when VPA is 0.4 to 3.45 V
4.8 V or more

P2138: 
Either of following conditions is met:
Condition A or B
Condition A
-
Difference between VPA and VPA 2 voltages
0.02 V or less
Condition B
-
VPA voltage
0.4 V or less
VPA2 voltage
1.2 V or less

COMPONENT OPERATING RANGE


Parameter
Standard Value
VPA voltage
0.4 V to 4.8 V
VPA2 voltage
1.2 V to 4.8 V
Difference between VPA and VPA2 voltages
More than 0.02 V

FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are set, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM


A105237E21


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM (ACCELERATOR PEDAL POSITION SENSOR)


    FI07052E14
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the values displayed on the tester.

    Standard voltage:
    Accelerator Pedal Operation
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A168219E06
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    A18-6 (VPA) - D35-18 (VPA)
    Always
    Below 1 Ω
    A18-5 (EPA) - D35-20 (EPA)
    Always
    Below 1 Ω
    A18-4 (VCPA) - D35-26 (VCPA)
    Always
    Below 1 Ω
    A18-3 (VPA2) - D35-19 (VPA2)
    Always
    Below 1 Ω
    A18-2 (EPA2) - D35-21 (EPA2)
    Always
    Below 1 Ω
    A18-1 (VCP2) - D35-27 (VCP2)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    A18-6 (VPA) or D35-18 (VPA) - Body ground
    Always
    10 kΩ or higher
    A18-5 (EPA) or D35-20 (EPA) - Body ground
    Always
    10 kΩ or higher
    A18-4 (VCPA) or D35-26 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A18-3 (VPA2) or D35-19 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A18-2 (EPA2) or D35-21 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A18-1 (VCP2) or D35-27 (VCP2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
OK


3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)


    A114634E10
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-26 (VCPA) - D35-20 (EPA)
    Ignition switch on (IG)
    4.5 to 5.0 V
    D35-27 (VCP2) - D35-21 (EPA2)
    Ignition switch on (IG)
    4.5 to 5.0 V

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPLACE ECM (Click here)
OK


4.REPLACE ACCELERATOR PEDAL ROD
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)