DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2121 | Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic) |
|
| Related DTCs | P2121: Accelerator pedal position sensor rationality |
| Required Sensors / Components (Main) | Accelerator position sensor sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Either of the following conditions is met. | Condition 1 or 2 |
| 1. Ignition switch | ON (IG) |
| 2. Electronic throttle actuator power | ON |
| Difference between VPA1 voltage (learned value) and VPA2 voltage (learned value) | Less than 0.4 V, or more than 1.2 V |
| 1.READ VALUE USING TECHSTREAM (ACCELERATOR PEAL POSITION SENSOR) |
![]() |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the values displayed on the tester.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2121 | A |
| No output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A18-6 (VPA) - D35-18 (VPA) | Always | Below 1 Ω |
| A18-5 (EPA) - D35-20 (EPA) | Always | Below 1 Ω |
| A18-4 (VCPA) - D35-26 (VCPA) | Always | Below 1 Ω |
| A18-3 (VPA2) - D35-19 (VPA2) | Always | Below 1 Ω |
| A18-2 (EPA2) - D35-21 (EPA2) | Always | Below 1 Ω |
| A18-1 (VCP2) - D35-27 (VCP2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A18-6 (VPA) or D35-18 (VPA) - Body ground | Always | 10 kΩ or higher |
| A18-5 (EPA) or D35-20 (EPA) - Body ground | Always | 10 kΩ or higher |
| A18-4 (VCPA) or D35-26 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A18-3 (VPA2) or D35-19 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A18-2 (EPA2) or D35-21 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A18-1 (VCP2) or D35-27 (VCP2) - Body ground | Always | 10 kΩ or higher |
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2121 | A |
| No output | B |
|
| ||||
| A | ||
| ||