Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.
The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter is used in order to convert the carbon monoxide (CO), hydrocarbon, and nitrogen oxides (HOx) into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio.
*: Value changes inside the ECM. Since the air fuel ratio sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A173183E01


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is more than 3.8 V
(b) Heated oxygen sensor voltage is 0.21 V or more
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  4. Intake system
  5. Fuel pressure
  6. Injector
  7. ECM
P2195
P2197
While fuel-cut operation is performed (during vehicle deceleration), air fuel ratio sensor current is 3.6 mA or more for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM
P2196
P2198
Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is less than 2.8 V
(b) Heated oxygen sensor voltage is less than 0.6 V
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  4. Intake system
  5. Fuel pressure
  6. Injector
  7. ECM
P2196
P2198
While fuel-cut operation is performed (during vehicle deceleration), air fuel ratio sensor current is less than 1.4 mA for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.
  5. When any of these DTCs are set, check the air fuel ratio sensor voltage output by selecting the following menu items on the Techstream: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Voltage B1 S1 or AFS Voltage B2 S1.
  6. Short-term fuel trim values can also be read using the Techstream.
  7. The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the Techstream.
  8. If an air fuel ratio sensor malfunction is detected, the ECM sets a DTC.


MONITOR DESCRIPTION

Sensor voltage detection monitor
  1. Under the air fuel ratio feedback control, if the air fuel ratio sensor voltage output indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the air fuel ratio sensor. The ECM illuminates the MIL and sets a DTC.
Example:
  1. If the air fuel ratio sensor voltage output is less than 2.8 V (very rich condition) for 10 seconds, despite the heated oxygen sensor voltage output being less than 0.6 V, the ECM sets DTC P2196. Alternatively, if the air fuel ratio sensor voltage output is more than 3.8 V (very lean condition) for 10 seconds, despite the heated oxygen sensor voltage output being 0.15 V or more, DTC P2195 is set.
Sensor current detection monitor
  1. A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.
  2. If the air fuel ratio sensor output is 3.6 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and sets DTC P2195 (high-side stuck). If the air fuel ratio sensor output is 1.0 mA or less for more than 3 seconds of cumulative time, the ECM sets DTC P2196 (low-side stuck).

G034989E06


MONITOR STRATEGY


Related DTCs
P2195: Air fuel ratio sensor (Bank 1) signal stuck lean
P2196: Air fuel ratio sensor (Bank 1) signal stuck rich
P2197: Air fuel ratio sensor (Bank 2) signal stuck lean
P2198: Air fuel ratio sensor (Bank 2) signal stuck rich
Required Sensors / Components (Main)
Air fuel ratio sensor
Required Sensors / Components (Related)
Heated oxygen sensor
Frequency of Operation
Continuous
Duration
Sensor voltage detection monitor: 10 seconds
Sensor current detection monitor: 3 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
The monitor will run whenever these DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (A/F sensor heater)
P0100, P0102, P0103 (MAF meter)
P0110, P0112, P0113 (IAT sensor)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (CKP sensor)
P0450, P0451, P0452, P0453 (EVAP system)
P0500 (Vehicle speed sensor)
P0505 (Idle speed control) (IAC valve)

Sensor voltage detection monitor (Lean side malfunction P2195, P2197): 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor voltage detection monitor (Rich side malfunction P2196, P2198): 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor Current detection monitor P2195, P2196, P2197, P2198 
Battery voltage
11 V or more
Atmospheric pressure
0.75 or more
Air fuel ratio sensor status
Activated
Engine coolant temperature
75°C (167°F) or more
Continuous time of fuel-cut
3 to 10 seconds

TYPICAL MALFUNCTION THRESHOLDS


Sensor voltage detection monitor (Lean side malfunction P2195, P2197): 
Air fuel ratio sensor voltage
More than 3.8 V
Rear HO2S voltage
Rises from less than 0.21 V to 0.59 V or more

Sensor voltage detection monitor (Rich side malfunction P2196, P2198): 
Air fuel ratio sensor voltage
Less than 2.8 V
Rear HO2S voltage
Falls from 0.59 V or more to less than 0.21 V

Sensor current detection monitor (High side malfunction P2195, P2197): 
Air fuel ratio sensor current during fuel cut
3.6 mA or more

Sensor current detection monitor (Rich side malfunction P2196, P2198): 
Air fuel ratio sensor current during fuel cut
Less than 1.4 mA

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM


A172770E01


CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in steps 4, 7, 17, and 21 of the following diagnostic troubleshooting procedure when using the Techstream.

A107162E43


A107163E30

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch on (IG).
  3. Turn the tester on.
  4. Clear the DTCs (Click here).
  5. Start the engine, and warm it up until the ECT reaches 70°C (158°F) or higher (Procedure "A").
  6. Select the following menu items: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
  7. Drive the vehicle at between 38 mph (61 km/h) and 75 mph (120 km/h) for at least 10 minutes (Procedure "B").
  8. Change the transmission to the 2nd gear (Procedure "C").
  9. Drive the vehicle at a proper vehicle speed to perform fuel-cut operation (refer to the following HINT) (Procedure "D").

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Engine speed is 2500 rpm or more (fuel injection resumes at 1000 rpm).

  10. Accelerate the vehicle to 40 mph (64 km/h) or more by depressing the accelerator pedal for at least 10 seconds (Procedure "E").
  11. Soon after performing procedure "J" on the previous page, release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel-cut control (Procedure "F").
  12. Allow the vehicle to decelerate until the vehicle speed declines to less than 6 mph (10 km/h).
  13. Repeat procedures from "H" through "K" in this section at least 3 times per driving cycle.

    HINT:
    Completion of all air fuel ratio sensor monitors is required to change the value in TEST RESULT.

    CAUTION:
    Strictly observe posted speed limits, traffic laws, and road conditions when performing these driving patterns.


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

  1. The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Start the engine and turn the tester on.
    3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
    4. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
    6. Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

      HINT:
      1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
      2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


      Standard voltage:

      Tester Display
      Injection Volumes
      Status
      Voltages
      AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio)
      +25%
      Rich
      Less than 3.1 V
      AFS Voltage B1S1 Voltage or AFS B2S1 (Air fuel ratio)
      -12.5%
      Lean
      More than 3.5 V
      O2S B1S2 or O2S B2S2 (Heated oxygen)
      +25%
      Rich
      More than 0.55 V
      O2S B1S2 or O2S B2S2 (Heated oxygen)
      -12.5%
      Lean
      Less than 0.4 V

      NOTICE:
      The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


      Case
      Air Fuel Ratio Sensor (Sensor 1)
      Output Voltage
      Heated Oxygen Sensor (Sensor 2)
      Output Voltage
      Main Suspected Trouble Area
      1
      A162605E07
      A162598E03
      -
      2
      A162596E03
      A162598E03
      1. Air fuel ratio sensor
      2. Air fuel ratio sensor heater
      3. Air fuel ratio sensor circuit
      3
      A162605E07
      A162596E03
      1. Heated oxygen sensor
      2. Heated oxygen sensor heater
      3. Heated oxygen sensor circuit
      4
      A162596E03
      A162596E03
      1. Fuel pressure
      2. Gas leakage from exhaust system
        (Air fuel ratio extremely lean or rich)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
    2. To display the graph, select the following menu items on the tester: Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1 S1 or AFS Voltage B2 S1 and O2S B1 S2 or O2S B2 S2. Then press the graph button on the Data List view.

      HINT:
      1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
      2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
      3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197 or P2198
    A
    P2195, P2196, P2197 or P2198 and other DTCs
    B

    HINT:
    If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (TEST VALUE OF AIR FUEL RATIO SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Allow the vehicle to drive in accordance with the driving pattern described in the CONFIRMATION DRIVING PATTERN.

  1. Select the following menu items: Powertrain / Engine and ECT / Monitor / O2 Sensor.

  1. Check that the status of O2 Sensor is Complete.
    If the status is still Incomplete, drive the vehicle according to the driving pattern again.

  1. Select the following menu items: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RANGE B1S1.

  1. Check the test value of the air fuel ratio sensor output current during fuel-cut.

    Result:

    Test Value
    Proceed to
    Within normal range (1.4 mA or more, and less than 3.6 mA)
    A
    Outside normal range (Less than 1.4 mA, or 3.6 mA or more)
    B



B
Go to step 19
A


3.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Voltage B1 S1 or AFS Voltage B2 S1 and Engine Speed.



  1. Check the air fuel ratio sensor voltage 3 times, when the engine is in each of the following conditions:

    1. While idling (check for at least 30 seconds) (Step (1))

    2. At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed) (Step (2))



    3. Raise the engine speed to 4000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed (Step (3)).

      Standard voltage:

      Conditions
      Air Fuel Ratio Sensor Voltage Variations
      Reference
      Steps (1) and (2)
      Changes at approximately 3.3 V
      Between 3.1 V and 3.5 V
      Step (3)
      Increases to 3.8 V or more
      This occurs during engine deceleration (when fuel-cut performed)

      HINT:
      For more information, see the diagrams below.


      A072304E26

      HINT:
      1. If the output voltage of the air fuel ratio sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those described on the previous page, the air fuel ratio sensor may have an open circuit. (This will also happen if the air fuel ratio sensor heater has an open circuit.)
      2. If the output voltage of the air fuel ratio sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those described on the previous page, the air fuel ratio sensor may have a short circuit.
      3. The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the air fuel ratio sensor output voltage.
      4. The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 10 mph (16 km/h) to allow the ECM to learn the closed throttle valve position.
      5. When the vehicle is driven:
        The output voltage of the air fuel ratio sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The air fuel ratio sensor is functioning normally.
      6. The air fuel ratio sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the air fuel ratio sensor or ECM will show a constant voltage result.



NG
Go to step 10
OK


4.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read DTCs using the Techstream.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197 or P2198
    A
    No output
    B



B
Go to step 9
A


6.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


7.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read the DTCs using the Techstream.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198
    B



B
REPLACE ECM (Click here)
A

END 

9.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
CHECK FOR INTERMITTENT PROBLEMS
YES

DTC CAUSED BY RUNNING OUT OF FUEL 

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A126269E39
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    HA1A (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HA1A (1) - A1A- (4)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    HA2A (1) - +B (2)
    20°C (68°F)
    1.8 to 3.4 Ω
    HA2A (1) - A2A- (4)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)


    A136175E14
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B2-2 (HA1A)
    Always
    Below 1 Ω
    B20-3 (A1A+) - B2-22 (A1A+)
    Always
    Below 1 Ω
    B20-4 (A1A-) - B2-30 (A1A-)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) - B2-1 (HA2A)
    Always
    Below 1 Ω
    B19-3 (A2A+) - B2-23 (A2A+)
    Always
    Below 1 Ω
    B19-4 (A2A-) - B2-31 (A2A-)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B2-2 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B20-3 (A1A+) or B2-22 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B20-4 (A1A-) or B2-30 (A1A-) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) or B2-1 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B19-3 (A2A+) or B2-23 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B19-4 (A2A-) or B2-31 (A2A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


12.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage.

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13.CHECK FUEL PRESSURE (HIGH PRESSURE SIDE AND LOW PRESSURE SIDE)
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


14.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


15.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


16.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes / Pending.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198
    B



B
REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A

END 

18.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


19.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


20.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Read the DTCs using the Techstream.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes / Pending.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198 (Air fuel ratio sensor pending DTCs)
    B



B
REPLACE ECM (Click here)
A

END