UNLOCK WARNING SWITCH > INSTALLATION |
| 1. INSTALL UN-LOCK WARNING SWITCH ASSEMBLY |
![]() |
Engage the 2 claws to install the un-lock warning switch assembly to the steering lock sub-assembly.
| 2. INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY |
Make sure that the ignition switch lock cylinder assembly is in the ACC position.
![]() |
Install the ignition switch lock cylinder assembly to the steering lock sub-assembly.
Make sure that the ignition switch lock cylinder assembly is securely installed.
| 3. INSPECT STEERING LOCK OPERATION |
![]() |
Check that the steering lock mechanism is activated when the key is removed.
![]() |
Check that the steering lock mechanism is deactivated when the key is inserted and turned to the ACC position.
| 4. INSTALL STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY |
Temporarily install the assembled steering lock and its bracket to the steering column assembly with 2 new tapered-head bolts.
![]() |
Tighten the 2 tapered-head bolts until the bolt heads break off.
| 5. INSTALL KEY CYLINDER LIGHT ASSEMBLY (w/o Engine Immobiliser System) |
Align the key cylinder light assembly with the upper bracket. Tilt the amplifier slightly and slide it into the position as shown in the illustration.
![]() |
Push the key cylinder light assembly to install it to the upper bracket with the 2 claws.
| 6. INSTALL TRANSPONDER KEY AMPLIFIER (w/ Engine Immobiliser System) |
![]() |
Align the transponder key amplifier with the upper bracket. Tilt the amplifier slightly and slide it into the position as shown in the illustration.
Push the transponder key amplifier to install it to the upper bracket with the 2 claws.
| 7. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft sub-assembly and the steering column assembly.
![]() |
Install a new bolt.
| 8. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Check that the 2 bushings are securely installed to the steering column assembly.
![]() |
Install the steering column assembly with the bolt and 2 nuts.
Connect the connectors and engage the wire harness clamps to the steering column assembly.
![]() |
Connect the connector to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
| 9. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.
![]() |
Install a new bolt.
![]() |
Install the steering intermediate shaft sub-assembly to the steering column hole shield.
![]() |
Tighten the bolt.
| 10. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY |
![]() |
Engage the 2 claws to install the No. 1 air duct sub-assembly.
| 11. POSITION FRONT WHEELS STRAIGHT AHEAD |
| 12. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE |
![]() |
Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 13. INSTALL STEERING COLUMN COVER |
![]() |
Engage the claw to install the upper steering column cover.
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 2 screws.
| 14. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
![]() |
Install the brake pedal support sub-assembly with the 4 nuts.
![]() |
Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.
![]() |
Connect the brake pedal load sensing switch connector and engage the clamp.
| 15. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Apply lithium soap base glycol grease to the push rod pin.
Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.
| 16. INSTALL BRAKE PEDAL RETURN SPRING |
![]() |
Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.
| 17. INSTALL STOP LIGHT SWITCH ASSEMBLY |
![]() |
Temporarily install the stop light switch assembly with the stop light switch lock nut.
![]() |
Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).
Tighten the stop light switch lock nut.
![]() |
Connect the connector.
| 18. INSPECT AND ADJUST BRAKE PEDAL HEIGHT |
Check the brake pedal height.
![]() |
Turn back the carpet.
Measure the shortest distance between the brake pedal surface and tibia pad.
Adjust the brake pedal height.
Disconnect the stop light switch connector.
Remove the stop light switch assembly.
Loosen the push rod clevis lock nut.
Adjust the brake pedal height by turning the push rod.
Tighten the push rod clevis lock nut.
Install and adjust the stop light switch .
Connect the stop light switch connector.
| 19. INSPECT BRAKE PEDAL FREE PLAY |
![]() |
Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.
Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.
| 20. INSPECT BRAKE PEDAL RESERVE DISTANCE |
![]() |
Release the parking brake lever.
With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.
| 21. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Install the DLC3 to the driver side knee airbag assembly with the 2 claws.
![]() |
Connect the driver side knee airbag connector and tire pressure warning reset switch connector to the driver side knee airbag assembly.
![]() |
Support the driver side knee airbag assembly with one hand as shown in the illustration.
![]() |
Temporarily install the driver side knee airbag assembly with the 2 hooks.
![]() |
Install the driver side knee airbag assembly with the 4 bolts.
| 22. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System) |
![]() |
Connect the hood lock control cable assembly.
Connect each connector.
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 23. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Connect the hood lock control cable assembly.
Connect each connector and the aspirator duct.
![]() |
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 24. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the claw and clip, install the cowl side trim sub-assembly LH.
Install the clip.
| 25. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the guide and the 8 claws, and install the front door scuff plate LH.
| 26. ADJUST SPIRAL CABLE |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Rotate the spiral cable counterclockwise slowly by hand until it stops.
![]() |
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
| 27. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 28. INSPECT STEERING WHEEL CENTER POINT |
| 29. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Support the steering pad with one hand as shown in the illustration.
![]() |
Connect the 2 airbag connectors to the steering pad.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
![]() |
Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
| 30. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Install the lower No. 3 steering wheel cover with the claw.
| 31. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Install the lower No. 2 steering wheel cover with the claw.
| 32. INSTALL FRONT WHEEL LH |
| 33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 34. INSPECT STEERING PAD |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 35. INSPECT SRS WARNING LIGHT |