Home › ENGINE › 2GR-FE COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



2. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



3. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



4. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



5. REMOVE COOL AIR INTAKE DUCT SEAL


    A170196
  1. Remove the 11 clips and cool air intake duct seal.



6. REMOVE BATTERY

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    A175880
  1. Loosen the nut, and disconnect the negative battery terminal.

  1. Loosen the nut, and disconnect the positive battery terminal.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



7. REMOVE NO. 2 AIR CLEANER INLET


    A170453
  1. Disconnect the 2 vacuum switching valve clamps.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.



8. REMOVE NO. 1 AIR CLEANER INLET


    A170454
  1. Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.



9. DISCONNECT NO. 1 RADIATOR HOSE


    A169427
  1. Disconnect the No. 1 radiator hose from the radiator.



10. DISCONNECT NO. 2 RADIATOR HOSE


    A169428
  1. Disconnect the No. 2 radiator hose from the radiator.



11. DISCONNECT OIL COOLER HOSE


    A169429
  1. Disconnect the oil cooler hoses from the radiator.



12. DISCONNECT COOLING FAN ECU CONNECTOR


    A169435
  1. Detach the wire harness clamps from the fan shroud LH side.



    A169436
  1. Detach the wire harness clamps from the fan shroud RH side and disconnect the cooling fan ECU connector.



13. REMOVE RADIATOR GRILLE


    B172749E01
  1. Put protective tape around the radiator grille.



    B172746
  1. Remove the 2 bolts and 4 clips.



    B172747
  1. Disengage the 6 claws and 4 guides, and remove the radiator grille.



14. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    B174188
  1. Remove the hood lock nut cap.



    B174189
  1. Remove the 3 bolts.



    B174190
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



15. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    B174191
  1. Disconnect the connector.



    B174192
  1. Remove the hood lock nut cap.



    B174193
  1. Remove the 3 bolts.



    B174194
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



16. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A169432
  1. Disconnect the low pitched horn and high pitched horn connectors.



    A169469
  1. Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.



17. SEPARATE COOLER CONDENSER ASSEMBLY


    A169439
  1. Remove the 4 bolts and move the cooler condenser assembly to remove the radiator assembly and fan assembly with motor.



18. REMOVE RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR


    A169440
  1. Remove the radiator assembly and fan assembly with motor.



19. REMOVE FAN ASSEMBLY WITH MOTOR


    A169443
  1. Disconnect the radiator reserve tank hose or pipe from the radiator assembly.



    A169446E01
  1. Remove the 3 bolts.

  1. Pull up the fan assembly with motor from the radiator assembly to remove the fan assembly with motor.



20. REMOVE RADIATOR SUPPORT CUSHION


    A169437
  1. Remove the 2 radiator support cushions.



21. REMOVE LOWER RADIATOR SUPPORT


    A169444
  1. Remove the 2 lower radiator supports.