Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

DTC    B2341    Sensor (Motor) Failure

DTC    B2344    Position Failure

for Preparation Click here


DESCRIPTION

When the sliding roof drive gear sub-assembly (sliding roof control ECU) detects malfunctions in the motor, and the sliding roof operation is stopped, DTC B2341 is output. When the sliding roof drive gear sub-assembly (sliding roof control ECU) detects malfunctions in the gear, and the sliding roof operation is stopped, DTC B2344 is output.

DTC No.
DTC Detection Condition
Trouble Area
B2341
Sensor (motor) failure
  1. Sliding roof drive gear sub-assembly (sliding roof control ECU)
  2. Roof console box assembly (sliding roof switch assembly)
  3. Wire harness
B2344
Position failure
  1. Sliding roof drive gear sub-assembly (sliding roof control ECU)
  2. Roof console box assembly (sliding roof switch assembly)
  3. Wire harness

WIRING DIAGRAM


B131103E07


INSPECTION PROCEDURE

1.CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the OPEN and UP switches (Click here).

    OK:
    Auto operation operates normally with OPEN and UP switches.



NG
Go to step 3
OK


2.RECHECK FOR DTC
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If DTCs are detected frequently, replace the ECU.

    OK:
    DTC is not output.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END 

3.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
  1. Check that the sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized (Click here).

    OK:
    Sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized.



NG
Go to step 6
OK


4.CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the OPEN and UP switches (Click here).

    OK:
    Auto operation operates normally with OPEN and UP switches.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK


5.RECHECK FOR DTC
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If DTCs are detected frequently, replace the ECU.

    OK:
    DTC is not output.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END 

6.INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)


    B174030E02
  1. Remove the roof console box assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Q1-3 (CLS) - Q1-2 (GND)
    CLOSE
    Below 100 Ω
    Q1-4 (OPN) - Q1-2 (GND)
    OPEN
    Below 100 Ω
    Q1-5 (DOWN) - Q1-2 (GND)
    DOWN
    Below 100 Ω
    Q1-6 (UP) - Q1-2 (GND)
    UP
    Below 100 Ω
    Q1-3 (CLS) - Q1-2 (GND)
    OPEN
    1 kΩ or higher
    Q1-4 (OPN) - Q1-2 (GND)
    CLOSE
    1 kΩ or higher
    Q1-5 (DOWN) - Q1-2 (GND)
    UP
    1 kΩ or higher
    Q1-6 (UP) - Q1-2 (GND)
    DOWN
    1 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)
OK


7.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)


    B174031E02
  1. Disconnect the Q12 and Q1 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Q1-2 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q1-4 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q1-5 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q1-3 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q1-6 (UP)
    Always
    Below 1 Ω
    Q1-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q1-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q1-2 (GND) - Body ground
    Always
    Below 1 Ω
    Q1-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q1-6 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)