Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

DTC    B2342    Switch Failure

for Preparation Click here


DESCRIPTION

This DTC is output when the sliding roof drive gear sub-assembly (sliding roof control ECU) detects that the OPEN, CLOSE, UP or DOWN switch in the roof console box assembly (sliding roof switch assembly) is stuck for 30 seconds or more.

DTC No.
DTC Detection Condition
Trouble Area
B2342
Sliding roof drive gear sub-assembly (sliding roof control ECU) detects OPEN, CLOSE, UP or DOWN switch in roof console box assembly (sliding roof switch assembly) is stuck for 30 seconds or more
  1. Sliding roof drive gear sub-assembly (sliding roof control ECU)
  2. Roof console box assembly (sliding roof switch assembly)
  3. Wire harness

WIRING DIAGRAM

Refer to DTC B2341 .

INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (SLIDE OPEN AND TILT UP SWITCH)
  1. Use the DATA LIST to check if the sliding roof switch assembly is functioning properly.

    Slide Roof 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch
    Slide switch open signal/ON or OFF
    ON: OPEN switch is pressed.
    OFF: OPEN switch is not pressed.
    -
    Close Switch
    Slide switch close signal/ON or OFF
    ON: CLOSE switch is pressed.
    OFF: CLOSE switch is not pressed.
    -
    Up Switch
    Tilt switch up signal/ON or OFF
    ON: UP switch is pressed.
    OFF: UP switch is not pressed.
    -
    Down Switch
    Tilt switch down signal/ON or OFF
    ON: DOWN switch is pressed.
    OFF: DOWN switch is not pressed.
    -

    OK:
    Techstream displays as shown in the table according to the operation of each switch.



NG
Go to step 4
OK


2.CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the OPEN and UP switches (Click here).

    OK:
    Auto operation operates normally with OPEN and UP switches.



NG
Go to step 8
OK


3.RECHECK FOR DTC
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If DTCs are detected frequently, replace the ECU.

    OK:
    DTC is not output.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END 

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)


    B174030E02
  1. Remove the roof console box assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Q1-3 (CLS) - Q1-2 (GND)
    CLOSE
    Below 100 Ω
    Q1-4 (OPN) - Q1-2 (GND)
    OPEN
    Below 100 Ω
    Q1-5 (DOWN) - Q1-2 (GND)
    DOWN
    Below 100 Ω
    Q1-6 (UP) - Q1-2 (GND)
    UP
    Below 100 Ω
    Q1-3 (CLS) - Q1-2 (GND)
    OPEN
    1 kΩ or higher
    Q1-4 (OPN) - Q1-2 (GND)
    CLOSE
    1 kΩ or higher
    Q1-5 (DOWN) - Q1-2 (GND)
    UP
    1 kΩ or higher
    Q1-6 (UP) - Q1-2 (GND)
    DOWN
    1 kΩ or higher



NG
Go to step 6
OK


5.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)


    B174031E02
  1. Disconnect the Q12 and Q1 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Q1-2 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q1-4 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q1-5 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q1-3 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q1-6 (UP)
    Always
    Below 1 Ω
    Q1-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q1-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q1-2 (GND) - Body ground
    Always
    Below 1 Ω
    Q1-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q1-6 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)  

6.REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)
  1. Temporarily replace the roof console box assembly (sliding roof switch assembly) with a new one or normally functioning one (Click here).

  1. Perform the initialization (Click here)


NEXT


7.RECHECK FOR DTC
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If DTCs are detected frequently, replace the ECU.

    OK:
    DTC is not output.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END 

8.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
  1. Check that the sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized (Click here).

    OK:
    Sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized.



NG
Go to step 11
OK


9.CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the OPEN and UP switches (Click here).

    OK:
    Auto operation operates normally with OPEN and UP switches.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK


10.RECHECK FOR DTC
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If DTCs are detected frequently, replace the ECU.

    OK:
    DTC is not output.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END 

11.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)


    B174031E02
  1. Disconnect the Q12 and Q1 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Q1-2 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q1-4 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q1-5 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q1-3 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q1-6 (UP)
    Always
    Below 1 Ω
    Q1-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q1-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q1-2 (GND) - Body ground
    Always
    Below 1 Ω
    Q1-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q1-6 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)