DTC P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2714 | ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine, intermediate and the output shaft, and also by the oil pressure. (2-trip detection logic) |
|
| Related DTCs | P2714: Shift solenoid valve SLT/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLT, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | 0.5 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) | P0712, P0713 (ATF temperature sensor circuit) P0717 (Turbine speed sensor circuit) P0793 (Intermediate shaft speed sensor circuit) P0500 (Vehicle speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P2769, P2770 (Shift solenoid valve DSL circuit) P2716 (Shift solenoid valve SLT circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0505, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (Electronic throttle system (if applicable)) |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -20°C (-4°F) or more |
| ECM selected gear | 1st |
| Temporary MAIN gear | 1st or 2nd or 3rd or 4th |
| NT - NC x Temporary MAIN gear ratio NT: Input (turbine) speed NC: Intermediate shaft speed | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| Temporary U/D gear | Low or High |
| NC - NO x Temporary U/D gear ratio NO: Output speed | 300 rpm or more at Output speed 1000 rpm |
| TT TT: Turbine Torque | 900 Nm or more |
| NT | 250 rpm or more |
| NC | 250 rpm or more |
| NO | 250 rpm or more |
| ECM selected gear | 2nd |
| Temporary MAIN gear | 1st or 2nd or 3rd or 4th |
| NT - NC x Temporary MAIN gear ratio NT: Input (turbine) speed NC: Intermediate shaft speed | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| Temporary U/D gear | Low or High |
| NC - NO x Temporary U/D gear ratio NO: Output speed | 300 rpm or more at Output speed 1000 rpm |
| TT TT: Turbine Torque | 192 Nm or more |
| NT | 250 rpm or more |
| NC | 250 rpm or more |
| NO | 250 rpm or more |
| ECM selected gear | 3rd |
| Temporary MAIN gear | 1st or 2nd or 3rd or 4th |
| NT - NC x Temporary MAIN gear ratio NT: Input (turbine) speed NC: Intermediate shaft speed | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| Temporary U/D gear | Low or High |
| NC - NO x Temporary U/D gear ratio NO: Output speed | 300 rpm or more at Output speed 1000 rpm |
| TT TT: Turbine Torque | 900 Nm or more |
| NT | 250 rpm or more |
| NC | 250 rpm or more |
| NO | 250 rpm or more |
| ECM selected gear | 4th or 5th |
| Temporary MAIN gear | 1st or 2nd or 3rd or 4th |
| NT - NC x Temporary MAIN gear ratio NT: Input (turbine) speed NC: Intermediate shaft speed | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| Temporary U/D gear | Low or High |
| NC - NO x Temporary U/D gear ratio NO: Output speed | 300 rpm or more at Output speed 1000 rpm |
| TT TT: Turbine Torque | 189 Nm or more |
| NT | 250 rpm or more |
| NC | 250 rpm or more |
| NO | 250 rpm or more |
| NT - NC x 1st gear ratio | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| NC - NO x Low gear ratio | 300 rpm or more at Output speed 1000 rpm |
| Duration | 0.5 sec. or more |
| NT - NC x 2rd gear ratio | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| NC - NO x Low gear ratio | 300 rpm or more at Output speed 1000 rpm |
| Duration | 0.5 sec. or more |
| NT - NC x 3rd gear ratio | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| NC - NO x Low gear ratio | 300 rpm or more at Output speed 1000 rpm |
| Duration | 0.5 sec. or more |
| Shift Solenoid valve SL1 Performance | Not performance malfunction |
| NT - NC x 4th gear ratio | 100 rpm or more at Intermediate shaft speed 1000 rpm |
| NC - NO x (Low (4th) or High (5th)) gear ratio | 300 rpm or more at Output speed 1000 rpm |
| Duration | 0.5 sec. or more |
| Shift Solenoid valve SL1 Performance | Not performance malfunction |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the Techstream main switch ON.
When you use Techstream:
Select the item "Powertrain / Engine and ECT / Trouble Codes".
Read the DTCs using Techstream.
| Result | Proceed to |
| P2714 | A |
| P2714 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLT |
![]() |
Remove the shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
|
| ||||
| OK | ||
| ||