Home › TRANSMISSION · U151F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


SYSTEM DESCRIPTION

The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the duty ratio (*) of the SLT solenoid valve to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle. For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then
Duty Ratio=A/(A+B) x 100(%)
C108924E02

DTC No.
DTC Detection Condition
Trouble Area
P2714
ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine, intermediate and the output shaft, and also by the oil pressure. (2-trip detection logic)
  1. Shift solenoid valve SLT remains closed
  2. Valve body is blocked
  3. Torque converter clutch
  4. Automatic transaxle (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

In any forward position, when the difference between the revolutions of the turbine, Intermediate and output shaft exceeds the specified value (varies with Intermediate, output speed) determined by the ECM, the ECM illuminates the MIL and outputs the DTC.
When shift solenoid valve SLT remains on, the oil pressure goes down and the clutch engagement force decreases.

NOTICE:
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


MONITOR STRATEGY


Related DTCs
P2714: Shift solenoid valve SLT/ON malfunction
Required sensors/Components
Shift solenoid valve SLT, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE)
Frequency of operation
Continuous
Duration
0.5 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ON malfunction: 
The monitor will run whenever this DTC is not present.
(Not circuit malfunction)
P0712, P0713 (ATF temperature sensor circuit)
P0717 (Turbine speed sensor circuit)
P0793 (Intermediate shaft speed sensor circuit)
P0500 (Vehicle speed sensor circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0798 (Shift solenoid valve SL3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P2769, P2770 (Shift solenoid valve DSL circuit)
P2716 (Shift solenoid valve SLT circuit)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0505, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (Electronic throttle system (if applicable))
Transmission range
"D"
TFT (Transmission fluid temperature)
-20°C (-4°F) or more

ON malfunction (a): 
ECM selected gear
1st
Temporary MAIN gear
1st or 2nd or 3rd or 4th
NT - NC x Temporary MAIN gear ratio
NT: Input (turbine) speed
NC: Intermediate shaft speed
100 rpm or more at Intermediate shaft speed 1000 rpm
Temporary U/D gear
Low or High
NC - NO x Temporary U/D gear ratio
NO: Output speed
300 rpm or more at Output speed 1000 rpm
TT
TT: Turbine Torque
900 Nm or more
NT
250 rpm or more
NC
250 rpm or more
NO
250 rpm or more

ON malfunction (b): 
ECM selected gear
2nd
Temporary MAIN gear
1st or 2nd or 3rd or 4th
NT - NC x Temporary MAIN gear ratio
NT: Input (turbine) speed
NC: Intermediate shaft speed
100 rpm or more at Intermediate shaft speed 1000 rpm
Temporary U/D gear
Low or High
NC - NO x Temporary U/D gear ratio
NO: Output speed
300 rpm or more at Output speed 1000 rpm
TT
TT: Turbine Torque
192 Nm or more
NT
250 rpm or more
NC
250 rpm or more
NO
250 rpm or more

ON malfunction (c): 
ECM selected gear
3rd
Temporary MAIN gear
1st or 2nd or 3rd or 4th
NT - NC x Temporary MAIN gear ratio
NT: Input (turbine) speed
NC: Intermediate shaft speed
100 rpm or more at Intermediate shaft speed 1000 rpm
Temporary U/D gear
Low or High
NC - NO x Temporary U/D gear ratio
NO: Output speed
300 rpm or more at Output speed 1000 rpm
TT
TT: Turbine Torque
900 Nm or more
NT
250 rpm or more
NC
250 rpm or more
NO
250 rpm or more

ON malfunction (d): 
ECM selected gear
4th or 5th
Temporary MAIN gear
1st or 2nd or 3rd or 4th
NT - NC x Temporary MAIN gear ratio
NT: Input (turbine) speed
NC: Intermediate shaft speed
100 rpm or more at Intermediate shaft speed 1000 rpm
Temporary U/D gear
Low or High
NC - NO x Temporary U/D gear ratio
NO: Output speed
300 rpm or more at Output speed 1000 rpm
TT
TT: Turbine Torque
189 Nm or more
NT
250 rpm or more
NC
250 rpm or more
NO
250 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

[ON malfunction]
Detection condition: Total accumulated time of ON malfunctions (a), (b), (c) and (d) is 1 second or more

ON malfunction (a): 
NT - NC x 1st gear ratio
100 rpm or more at Intermediate shaft speed 1000 rpm
NC - NO x Low gear ratio
300 rpm or more at Output speed 1000 rpm
Duration
0.5 sec. or more

ON malfunction (b): 
NT - NC x 2rd gear ratio
100 rpm or more at Intermediate shaft speed 1000 rpm
NC - NO x Low gear ratio
300 rpm or more at Output speed 1000 rpm
Duration
0.5 sec. or more

ON malfunction (c): 
NT - NC x 3rd gear ratio
100 rpm or more at Intermediate shaft speed 1000 rpm
NC - NO x Low gear ratio
300 rpm or more at Output speed 1000 rpm
Duration
0.5 sec. or more
Shift Solenoid valve SL1 Performance
Not performance malfunction

ON malfunction (d): 
NT - NC x 4th gear ratio
100 rpm or more at Intermediate shaft speed 1000 rpm
NC - NO x (Low (4th) or High (5th)) gear ratio
300 rpm or more at Output speed 1000 rpm
Duration
0.5 sec. or more
Shift Solenoid valve SL1 Performance
Not performance malfunction

INSPECTION PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG) and turn the Techstream main switch ON.

  1. When you use Techstream:
    Select the item "Powertrain / Engine and ECT / Trouble Codes".

  1. Read the DTCs using Techstream.

    Result:

    Result
    Proceed to
    P2714
    A
    P2714 and other DTCs
    B

    HINT:
    If any other codes besides "P2714" are output, perform the troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT SHIFT SOLENOID VALVE SLT


    G020767E92
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

OK:
The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)