Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › COMPRESSOR AND MAGNETIC CLUTCH

COMPRESSOR AND MAGNETIC CLUTCH > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent the airbag from deploying (Click here).



3. REMOVE FRONT WHEEL RH


4. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



5. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



6. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH


    B172795
  1. Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.



    B172796
  1. Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly.

  1. Remove the pad from the front fender moulding sub-assembly.

  1. Remove the 2 No. 4 clips from the front fender moulding sub-assembly.



    B172797E01
  1. Remove the front fender side protector from the front fender moulding sub-assembly.



7. REMOVE FRONT FENDER LINER RH


    B174753E01
  1. Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.



    B174750
  1. Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



    B174752
  1. Remove the 5 clips, 7 screws and front fender liner RH.



8. REMOVE FRONT FENDER APRON SEAL RH


    A171853
  1. Remove the 2 bolts, clip and front fender apron seal RH.



9. REMOVE V-RIBBED BELT


    A162386E01
  1. Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.

    SST
    09961-00950  



    A095070
  1. While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.



10. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



11. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



12. REMOVE COOL AIR INTAKE DUCT SEAL


    B172745
  1. Remove the 11 clips and cool air intake duct seal.



13. REMOVE BATTERY

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    A175880
  1. Loosen the nut, and disconnect the negative battery terminal.

  1. Loosen the nut, and disconnect the positive battery terminal.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



14. REMOVE NO. 2 AIR CLEANER INLET


    A170453
  1. Disconnect the 2 vacuum switching valve clamps.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.



15. REMOVE NO. 1 AIR CLEANER INLET


    A170454
  1. Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.



16. DISCONNECT NO. 1 RADIATOR HOSE


    A169427
  1. Disconnect the No. 1 radiator hose from the radiator.



17. DISCONNECT NO. 2 RADIATOR HOSE


    A169428
  1. Disconnect the No. 2 radiator hose from the radiator.



18. DISCONNECT OIL COOLER HOSE


    A169429
  1. Disconnect the oil cooler hoses from the radiator.



19. DISCONNECT COOLING FAN ECU CONNECTOR


    A169435
  1. Detach the wire harness clamps from the fan shroud LH side.



    A169436
  1. Detach the wire harness clamps from the fan shroud RH side and disconnect the cooling fan ECU connector.



20. REMOVE RADIATOR GRILLE


    B172749E01
  1. Put protective tape around the radiator grille.



    B172746
  1. Remove the 2 bolts and 4 clips.



    B172747
  1. Disengage the 6 claws and 4 guides, and remove the radiator grille.



21. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    B174188
  1. Remove the hood lock nut cap.



    B174189
  1. Remove the 3 bolts.



    B174190
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



22. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    B174191
  1. Disconnect the connector.



    B174192
  1. Remove the hood lock nut cap.



    B174193
  1. Remove the 3 bolts.



    B174194
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



23. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A169432
  1. Disconnect the low pitched horn and high pitched horn connectors.



    A169469
  1. Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.



24. SEPARATE COOLER CONDENSER ASSEMBLY


    A169439
  1. Remove the 4 bolts and move the cooler condenser assembly to remove the radiator assembly and fan assembly with motor.



25. REMOVE RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR


    A169440
  1. Remove the radiator assembly and fan assembly with motor.



26. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY


    E150345
  1. Remove the bolt and disconnect the discharge hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



27. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E150346
  1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



28. REMOVE COMPRESSOR AND MAGNETIC CLUTCH


    E150347
  1. Disengage the clamp.

  1. Disconnect the connector.



    E150348
  1. Disengage each clamp.

  1. Disconnect the connector.



    E151053
  1. Remove the 4 bolts and the compressor and magnetic clutch.