Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0606    ECM / PCM Processor

for Preparation Click here


DESCRIPTION

The ECM continuously monitors its internal processors (CPUs), heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC
DTC Setting Condition
Trouble Area
P0606
  1. ECM CPUs malfunction
  2. Heated oxygen sensor transistors malfunction
  1. Exhaust gas leak
  2. Heated oxygen Sensor
  3. ECM

MONITOR STRATEGY


Related DTC
P0606: ECM range check
Required sensors/Components (main)
ECM
Required sensors/Components (sub)
Accelerator pedal position sensor, throttle position sensor, Brake switch, Cruise control, heated oxygen sensor
Frequency of Operation
Continuous
Duration
60 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor runs whenever the following DTCs are not present
None
Engine
Running
Estimated heated oxygen sensor temperature
450 to 800°C (842 to 1472°F)

TYPICAL MALFUNCTION THRESHOLDS


Difference of main accelerator pedal position and sub accelerator pedal position
0.3 V or more
Difference of main throttle position and sub throttle position
0.3 V or more
Difference of main brake switch signal and sub brake switch signal
Different
Cruise control
Fail
Heated oxygen sensor transistors
Fail

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0606 is output
    A
    DTC P0606 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    B



A
Go to step 3
B


2.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flow chart.

    HINT:
    1. If P0136 or P0156 is output, troubleshoot for that DTC first . Then proceed to step 6.
    2. If P0137or P0157 is output, troubleshoot for that DTC first . Then proceed to step 6.
    3. If P0138 or P0158 is output, troubleshoot for that DTC first . Then proceed to step 6.
    4. If DTC P0606 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).



NEXT
Go to step 6

3.CHECK FOR EXHAUST GAS LEAK
  1. Allow the engine to idle and rev the engine.

  1. Check for exhaust gas leaks around the heated oxygen sensor.
    If any exhaust gas leaks are present, repair them and proceed to step 4. If no exhaust gas leaks are present, proceed to step 4.

    HINT:
    1. If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
    2. If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.


NEXT


4.PERFORM CONFIRMATION DRIVING PATTERN
  1. Clear the DTC (Click here).

  1. Connect the Techstream to the DLC3.

  1. Warm up the engine until the engine coolant temperature becomes 75° (167°F) or more.



  1. Perform the driving pattern.


    A144392E30

    1. Accelerate the vehicle to 50 mph (80 km/h) and stop the vehicle.

    2. Drive the vehicle at 38 to 50 mph (60 to 80 km/h) for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0606 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    A
    DTC P0606 is output
    B
    DTC is not output
    C



B
REPLACE ECM (Click here)

C
Go to step 6
A


5.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flow chart.

    HINT:
    1. If P0136 or P0156 is output, troubleshoot for that DTC first . Then proceed to step 6.
    2. If P0137or P0157 is output, troubleshoot for that DTC first . Then proceed to step 6.
    3. If P0138 or P0158 is output, troubleshoot for that DTC first . Then proceed to step 6.
    4. If DTC P0606 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).


NEXT


6.INSPECT ECM
  1. Clear the DTC (Click here).

  1. Stop the engine and wait for 30 minutes.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and allow it to idle for 2 minutes.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0606 is output
    A
    DTC is not output
    B



A
REPLACE ECM (Click here)
B

END