Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speed Signal Circuit

for Preparation Click here


DESCRIPTION

The meter CPU receives vehicle speed signals from this circuit. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage. The skid control ECU transmits vehicle speed signals as pulses to the meter CPU. A voltage of 12 V is output from the combination meter assembly and then input to the skid control ECU. The signal is changed to a pulse signal at the transistor in the combination meter assembly.
A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.
Each ECU controls the respective system based on the pulse signal.

HINT:
This circuit is used for another system, and is not used for combination meter operation.


WIRING DIAGRAM


E152375E01


INSPECTION PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)


    E146920E03
  1. Disconnect the E1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E1-9 (+S) - Body ground
    Ignition switch on (IG)
    4.5 to 14 V

    HINT:
    If any of the ECUs specified in the wiring diagram supplied power to the combination meter, the combination meter will output a waveform.



NG
Go to step 4
OK


2.INSPECT COMBINATION METER (OUTPUT VOLTAGE)
  1. Reconnect the E1 connector.



    E152384E01
  1. Disconnect the A24 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-11 (SP1) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
Go to step 12
OK


3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM)


    E152386E02
  1. Check the input waveform.

    1. Reconnect the A24 connector.

    2. Remove the combination meter assembly with the connector(s) still connected.

    3. Connect the oscilloscope to terminals E1-29 (SI) and body ground.

    4. Ignition switch on (IG).

    5. Turn the wheel slowly.

    6. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
REPLACE SKID CONTROL ECU (Click here)
OK

REPLACE COMBINATION METER (Click here)  

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - JUNCTION CONNECTOR)


    E152394E02
  1. Disconnect the junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-9 (+S) - E24-2
    Always
    Below 1 Ω
    E1-9 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)


  1. Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

    HINT:
    If voltage is not present, the circuit (ECU) was possibly the malfunctioning circuit. This is the circuit that will be diagnosed by following the A step that follows.



      E152393E02
    1. Disconnect the junction connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      E24-4 - Body ground
      Ignition switch on (IG)
      4.5 to 14 V
      D53-9 (*1) - Body ground
      Ignition switch on (IG)
      4.5 to 14 V
      E24-1 (*4) - Body ground
      Ignition switch on (IG)
      4.5 to 14 V
      E24-3 (*3) - Body ground
      Ignition switch on (IG)
      4.5 to 14 V
      D53-11 - Body ground
      Ignition switch on (IG)
      4.5 to 14 V

      *1: w/ Smart Key System
      *3: w/ Navigation System
      *4: for Separate Type Amplifier System

      Result:

      Result
      Proceed to
      Voltage is not present in one circuit.
      A
      Voltage is present in all the circuits.
      B



B
REPLACE JUNCTION CONNECTOR
A


6.SYSTEM CHECK
  1. Select the circuit that did not present the voltage in the step 6.

    Result:

    Tester Connection
    System that uses the circuit
    Proceed to
    D53-9 (*1) - Body ground
    Smart key system
    A
    D53-11 - Body ground
    SFI system or Tire pressure warning system (*3)
    B
    E24-3 (*2) - Body ground
    Navigation system
    C
    E24-4 - Body ground
    Audio/visual system
    D
    E24-1 (*4) - Body ground
    Separate type amplifier system
    E

    *1: w/ Smart Key System
    *2: w/ Navigation System
    *3: w/ Tire Pressure Warning System
    *4: for Separate Type Amplifier System



B
Go to step 8

C
Go to step 9

D
Go to step 10

E
Go to step 11
A


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU CIRCUIT)


    E156065E06
  1. Disconnect the D9 (*1) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-9 (SPD) (*1) - Body ground
    Always
    10 kΩ or higher

    *1: w/ Smart Key System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT, TIRE PRESSURE WARNING CIRCUIT)


    E152467E01
  1. Disconnect the D36 or D33 (*3) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-8 (SPD) - Body ground
    Always
    10 kΩ or higher
    D33-2 (SPD) (*3) - Body ground
    Always
    10 kΩ or higher

    *3: w/ Tire Pressure Warning System

    Result:

    Result
    Proceed to
    OK (for Engine Control System)
    A
    OK (for Tire Pressure Warning System (*3))
    B
    NG
    C



B
REPLACE TIRE PRESSURE WARNING ECU

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (for 2GR-FE)  

9.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER CIRCUIT)


    E152468E04
  1. Disconnect the E5 (*2) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E5-3 (SPD) (*2) - Body ground
    Always
    10 kΩ or higher

    *2: w/ Navigation System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER  

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER CIRCUIT)


    E152469E04
  1. Disconnect the E3 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-3 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER  

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER CIRCUIT)


    E152435E02
  1. Disconnect the N14 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N14-11 (SPD) (*4) - Body ground
    Always
    10 kΩ or higher

    *4: for Separate Type Amplifier System



B
REPLACE JUNCTION CONNECTOR

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE STEREO COMPONENT AMPLIFIER  

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)


    E152385E02
  1. Disconnect the E1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-11 (SP1) - E1-29 (SI)
    Always
    Below 1 Ω
    A24-11 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER (Click here)