ENGINE OIL COOLER > REMOVAL |
| 1. REMOVE BATTERY |
![]() |
Loosen the nut, and disconnect the negative battery terminal.
Loosen the nut, and disconnect the positive battery terminal.
Loosen the nut, and remove the bolt and battery clamp.
Remove the battery and battery tray.
| 2. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 11 clips and cool air intake duct seal.
| 3. REMOVE NO. 2 AIR CLEANER INLET |
![]() |
Disconnect the 2 vacuum switching valve clamps.
Disconnect the 2 vacuum hoses.
Remove the 2 bolts and No. 2 air cleaner inlet.
| 4. REMOVE NO. 1 AIR CLEANER INLET |
![]() |
Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.
| 5. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the 3 vacuum hoses.
![]() |
Loosen the No. 1 air cleaner hose clamp.
Disconnect the hose clamps and No. 2 ventilation hose.
Disconnect the mass air flow meter connector.
![]() |
Release the 2 clips, and remove the 2 bolts.
Remove the air cleaner cap sub-assembly and air cleaner filter element.
| 6. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Remove the 3 bolts, disconnect the hose and the connector, and remove the air cleaner case sub-assembly.
| 7. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.
| 8. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.

Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the 2 cylinder block drain cock plugs.
| 9. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil drain plug and gasket, and drain the oil into a container.
Clean and install the oil drain plug with a new gasket.
| 10. DISCONNECT NO. 1 RADIATOR HOSE |
![]() |
Disconnect the No. 1 radiator hose from the radiator.
| 11. REMOVE RADIATOR RESERVE TANK ASSEMBLY |
![]() |
Disconnect the hose [A].
Remove the 2 bolts [B] and radiator reserve tank assembly.
| 12. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Remove the oil level dipstick.
Remove the bolt and No. 2 engine oil level dipstick guide.
![]() |
Remove the O-rings from the No. 2 engine oil level dipstick guide.
| 13. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Disconnect the air fuel ratio sensor connector and remove the clamp.
![]() |
Remove the 3 bolts and No. 2 exhaust manifold heat insulator.
| 14. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 6 bolts, 2 clips and No. 1 engine under cover.
| 15. REMOVE ENGINE UNDER COVER ASSEMBLY |
![]() |
Remove the 2 bolts and engine under cover assembly RR.
![]() |
Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.
| 16. REMOVE NO. 2 ENGINE UNDER COVER |
![]() |
Remove the 2 bolts and No. 2 engine under cover.
| 17. REMOVE PROPELLER WITH CENTER BEARING SHAFT (for 4WD) |
![]() |
Depress the brake pedal and hold it.
Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.
![]() |
Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.
Remove the 4 nuts, 4 bolts and 4 washers.
![]() |
Remove the 4 bolts and 4 adjusting shims.
![]() |
Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.
![]() |
Insert SST into the transfer to prevent oil leakage.
| 18. REMOVE TAIL EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.
Remove the gasket from the center exhaust pipe assembly.
| 19. REMOVE CENTER EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.
Remove the gasket from the No. 3 exhaust pipe sub-assembly.
| 20. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY |
![]() |
Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.
![]() |
Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.
Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.
| 21. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.
![]() |
Loosen the bolt.
Remove the 2 nuts and front exhaust pipe assembly.
Remove the gasket from the front exhaust pipe assembly.
| 22. REMOVE NO. 2 MANIFOLD STAY |
![]() |
Remove the bolt, nut and No. 2 manifold stay.
| 23. REMOVE EXHAUST MANIFOLD ASSEMBLY LH |
![]() |
Remove the 6 nuts and exhaust manifold assembly LH.
Remove the gasket.
| 24. REMOVE ENGINE OIL COOLER |
![]() |
Remove the bolt, 2 clamps, and 4 clips, and disconnect the 2 water by-pass hoses.
![]() |
Remove the oil cooler union bolt, oil cooler assembly, and O-ring.