LUMBAR SUPPORT ADJUSTER ASSEMBLY > INSTALLATION |
| 1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY |
![]() |
Install the lumbar support adjuster assembly with the 2 screws.
Connect the connector.
| 2. INSTALL FRONT SEATBACK COVER WITH PAD |
Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.
![]() |
Engage the 4 claws and install the 2 front seat headrest supports.
![]() |
Install the front seatback cover bracket with the nut.
![]() |
Engage the hooks.
![]() |
Using hog ring pliers, install 5 new hog rings.
![]() |
Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings.
| 3. INSTALL FRONT SEAT CUSHION INNER SHIELD |
![]() |
Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.
![]() |
Engage the claw.
Install the front seat cushion inner shield with the screw.
| 4. INSTALL FRONT SEAT INNER BELT ASSEMBLY |
![]() |
Install the front seat inner belt assembly with the nut.
Connect each connector and clamp.
| 5. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY |
w/o Seat Cushion Front Edge Adjustment Function:
Connect the connector to the front power seat lumbar switch.
w/ Seat Cushion Front Edge Adjustment Function:
Engage the each clamps.
Connect the connector to the front power seat lumbar switch and the seat variable cushion switch.
![]() |
Engage the guide and the claw.
Install the front seat cushion shield assembly with the 5 screws.
![]() |
Engage the hooks.
| 6. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Engage the 4 claws and install the slide and vertical power seat switch knob.
| 7. INSTALL RECLINING POWER SEAT SWITCH KNOB |
![]() |
Engage the 2 claws and install the reclining power seat switch knob.
| 8. INSTALL FRONT SEAT ASSEMBLY |
Place the front seat assembly in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Temporarily install the front seat assembly with the 4 bolts.
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
Operate the power seat switch knob and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
| 9. INSTALL REAR INNER SEAT TRACK COVER |
![]() |
Engage the 2 claws and install the rear inner seat track cover.
| 10. INSTALL REAR OUTER SEAT TRACK COVER |
![]() |
Engage the 2 claws and install the rear outer seat track cover.
| 11. INSTALL FRONT INNER SEAT TRACK COVER |
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Engage the 2 claws and install the front inner seat track cover.
| 12. INSTALL FRONT OUTER SEAT TRACK COVER |
![]() |
Engage the 2 claws and install the front outer seat track cover.
| 13. INSTALL FRONT SEAT HEADREST ASSEMBLY |
![]() |
Install the front seat headrest assembly as shown in the illustration.
| 14. INSPECT FRONT SEAT ASSEMBLY |
Inspect the power seat operation.
w/ Seat Heater System:
Check the seat heater operation.
Turn the ignition switch on (IG).
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 15. INSPECT SRS WARNING LIGHT |