Home › ENGINE › 2GR-FE INTAKE › AIR CLEANER AND HOSE

AIR CLEANER AND HOSE > INSTALLATION

for Preparation Click here



1. INSTALL INTAKE AIR RESONATOR


    A170886
  1. Tighten the bolt to install the intake air resonator.



2. INSTALL NO. 1 AIR CLEANER HOSE


    A171940E01
  1. Align the tab on the air cleaner cap with the groove on the air cleaner hose and tighten the bolt.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)



3. INSTALL NO. 3 INTAKE AIR CONTROL VALVE ASSEMBLY


    A170448
  1. Engage the 2 claws and install the No. 3 intake air control valve assembly.



4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A170450
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.



5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A171941E01
  1. Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A170887
  1. Connect the 3 vacuum hoses.



    A171944
  1. Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.



6. INSTALL NO. 1 AIR CLEANER INLET


    A170454E01
  1. Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.



7. INSTALL NO. 2 AIR CLEANER INLET


    A170453
  1. Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.



8. INSTALL BATTERY

NOTICE:
When reconnected the cable, some systems need to be initialized. (Click here).



    A175880E02
  1. Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }

  1. Connect the positive battery terminal, and tighten the nut.

    Torque:
    Nut B:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Connect the negative battery terminal, and tighten the nut.

    Torque:
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }



9. INSTALL COOL AIR INTAKE DUCT SEAL


    A170196
  1. Install the cool air intake duct seal with the 11 clips.