Home › BODY › INTERIOR › FUEL LID LOCK CONTROL

FUEL LID LOCK CONTROL > INSTALLATION

for Preparation Click here



1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


  1. Engage the 9 clamps and install the fuel lid lock control cable sub-assembly.


    B173659



    B160347
  1. Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.



    B173658
  1. Connect the fuel lid lock control cable sub-assembly.



2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B173657
  1. Install the fuel lid lock open lever sub-assembly with the 2 screws.



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly LH with the 2 bolts.


    B173613



4. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170934E01
  1. Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.



5. INSTALL FRONT DECK SIDE TRIM COVER LH


    B175145
  1. Engage the 4 claws and install the 2 front deck side trim covers LH.



6. INSTALL NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Install the No. 2 deck side trim hook with the screw.



7. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    B173599
  1. for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



    B173601
  1. for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



8. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Engage the 10 claws and install the rear deck trim cover.



9. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Engage the 5 claws and install the reclining remote control bezel LH.



10. INSTALL REAR POWER OUTLET SOCKET COVER


    E151328
  1. Engage the 2 claws and install the rear power outlet socket cover.



11. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    E151490
  1. Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.



12. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    B173619
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.



13. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)


    B173597
  1. Engage the 10 claws and install the side trim cover LH.



14. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173681
  1. Connect each connector.



    B173680
  1. Engage the 4 claws and install the power outlet socket bezel.



15. INSTALL DECK SIDE TRIM LH


    B173624
  1. Engage the 3 guides and 4 claws as shown in the illustration.



    B173596
  1. Install the deck side trim LH with the bolt.



16. INSTALL DECK SIDE TRIM COVER LH


    B175144
  1. Engage the 2 claws and install the deck side trim cover LH.



17. INSTALL REAR FLOOR FINISH PLATE


    B173609
  1. Engage the 4 clips and the 4 claws, and install the rear floor finish plate.



18. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B205721
  1. Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



19. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    B170936
  1. Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



20. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



21. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.



22. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Install the rear deck floor box with the 2 nuts.



23. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Install the rear deck floor board assembly with the 4 nuts and 4 bolts.



24. INSTALL REAR MAT


25. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.



26. INSTALL DECK SIDE TRIM BOX LH


  1. Install the deck side trim box LH as shown in the illustration.


    B178555



    B173243E01
  1. Install the 2 deck side trim clip and the clips.



27. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Engage the 2 clips and install the rear seat side cover LH.



28. INSTALL DECK SIDE TRIM BOX RH


  1. Install the deck side trim box RH as shown in the illustration.


    B178553



    B173247E01
  1. Install the 2 deck side trim clip and the clip.



29. INSTALL JACK CARRIER ASSEMBLY


    B178549
  1. Engage the 3 claws, and install the jack carrier assembly.



30. INSTALL JACK ASSEMBLY


    B173245
  1. Install the jack assembly.



31. INSTALL JACK CARRIER CUSHION


    B178550
  1. Install the jack carrier cushion.



32. INSTALL JACK CARRIER SUPPORT


33. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    B173608
  1. Engage the 2 clips and install the rear seat side cover RH.



34. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    B175152
  1. Engage the 3 guides and 3 clips and install the rear No. 1 floor board.



35. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



36. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Engage the 2 guides and install the No. 2 deck board sub-assembly.



37. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Engage the 2 guides and install the No. 3 deck board sub-assembly.



38. INSTALL DECK BOARD ASSEMBLY


    B173240
  1. Install the deck board sub-assembly.



39. INSTALL LOWER CENTER PILLAR GARNISH LH


    B173231
  1. Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.



40. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B170910
  1. Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



41. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173233E01
  1. Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



42. INSTALL REAR DOOR SCUFF PLATE LH


    B173228
  1. Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.



43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B173239E01
  1. Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



44. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



45. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    B173778
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173780
  1. Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



46. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173771E01



    B174591
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



47. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



48. INSTALL REAR SEAT LEG SIDE COVER LH


    B173779
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



49. INSTALL REAR INNER TRACK BRACKET COVER LH


    B173777
  1. Engage the 4 claws and install the rear inner track bracket cover.



50. INSTALL REAR OUTER TRACK BRACKET COVER LH


    B173776
  1. Engage the 4 claws and install the rear outer track bracket cover.



51. INSTALL REAR SEAT TRACK BRACKET COVER LH


    B173775
  1. Engage the 8 claws and install the 2 rear seat track bracket covers.



52. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)


    B176351
  1. Install the rear seat headrest assembly as shown in the illustration.



53. INSTALL REAR CENTER SEAT ASSEMBLY


54. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    B173764
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173774
  1. Temporarily Install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



55. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.



56. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



57. INSTALL REAR SEAT LEG SIDE COVER RH


    B173765
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



58. INSTALL REAR INNER TRACK BRACKET COVER RH


    B173761
  1. Engage the 4 claws and install the rear inner track bracket cover.



59. INSTALL REAR OUTER TRACK BRACKET COVER RH


    B204931
  1. Engage the 5 claws and install the rear outer track bracket cover.



60. INSTALL REAR SEAT TRACK BRACKET COVER RH


    B173760
  1. Engage the 8 claws and install the 2 seat track bracket covers.



61. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)


    B176352
  1. Install the rear seat headrest assembly as shown in the illustration.



62. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B174588E01
  1. Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B174587E01
  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



63. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for Manual Seat)
  1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
    If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.



64. INSTALL REAR SEAT TRACK COVER LH (for Manual Seat)


    B180417
  1. Engage the 4 claws and install the 2 rear seat track covers.



65. INSTALL FRONT INNER SEAT TRACK COVER LH (for Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B174584
  1. Engage the 2 claws and install the front inner seat track cover.



66. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Manual Seat)


    B174583
  1. Engage the 2 claws and install the front outer seat track cover.



67. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)


    B176350
  1. Install the front seat headrest assembly as shown in the illustration.



68. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When reconnected the cable, some systems need to be initialized (Click here).

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B174582E01
  1. Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Operate the power seat switch knob and move the seat to the foremost position.



    B174581E01
  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



69. INSTALL REAR INNER SEAT TRACK COVER LH (for Power Seat)


    B172844
  1. Engage the 2 claws and install the rear inner seat track cover.



70. INSTALL REAR OUTER SEAT TRACK COVER LH (for Power Seat)


    B172843
  1. Engage the 2 claws and install the rear outer seat track cover.



71. INSTALL FRONT INNER SEAT TRACK COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B172842
  1. Engage the 2 claws and install the front inner seat track cover.



72. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Power Seat)


    B172841
  1. Engage the 2 claws and install the front outer seat track cover.



73. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)


    B176350
  1. Install the front seat headrest assembly as shown in the illustration.



74. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here.)



75. INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
  1. Inspect the power seat operation.

  1. w/ Seat Heater System:
    Check the seat heater operation.

    1. Turn the ignition switch on (IG).

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.



76. INSPECT SRS WARNING LIGHT
(Click here)