FUEL LID LOCK CONTROL > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag) |
| 2. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat) |
![]() |
Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.
![]() |
Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.
| 3. REMOVE FRONT OUTER SEAT TRACK COVER LH (for Manual Seat) |
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Disengage the 2 claws and remove the front outer seat track cover.
| 4. REMOVE FRONT INNER SEAT TRACK COVER LH (for Manual Seat) |
![]() |
Disengage the 2 claws and remove the front inner seat track cover.
| 5. REMOVE REAR SEAT TRACK COVER LH (for Manual Seat) |
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Disengage the 4 claws and remove the 2 rear seat track covers.
| 6. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat) |
![]() |
Remove the 2 bolts on the rear side of the seat.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Remove the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.
Disconnect the connectors under the front seat assembly.
Remove the front seat assembly.
| 7. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat) |
![]() |
Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.
![]() |
Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.
| 8. REMOVE FRONT OUTER SEAT TRACK COVER LH (for Power Seat) |
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Disengage the 2 claws and remove the front outer seat track cover.
| 9. REMOVE FRONT INNER SEAT TRACK COVER LH (for Power Seat) |
![]() |
Disengage the 2 claws and remove the front inner seat track cover.
| 10. REMOVE REAR OUTER SEAT TRACK COVER LH (for Power Seat) |
Operate the power seat switch knob and move the seat to the foremost position.
![]() |
Disengage the 2 claws and remove the rear outer seat track cover.
| 11. REMOVE REAR INNER SEAT TRACK COVER LH (for Power Seat) |
![]() |
Disengage the 2 claws and remove the rear inner seat track cover.
| 12. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat) |
![]() |
Remove the 2 bolts on the rear side of the seat.
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Remove the 2 bolts on the front side of the seat.
Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.
Disconnect the cable from the negative (-) battery terminal.
Disconnect each connector under the front seat assembly.
Remove the front seat assembly.
| 13. REMOVE REAR CENTER SEAT ASSEMBLY |
| 14. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side) |
![]() |
Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.
![]() |
Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.
| 15. REMOVE REAR SEAT TRACK BRACKET COVER LH |
![]() |
Disengage the 8 claws and remove the 2 rear seat track bracket covers.
| 16. REMOVE REAR OUTER TRACK BRACKET COVER LH |
![]() |
Disengage the 4 claws and remove the rear outer track bracket cover.
| 17. REMOVE REAR INNER TRACK BRACKET COVER LH |
![]() |
Disengage the 4 claws and remove the rear inner track bracket cover.
| 18. REMOVE REAR SEAT LEG SIDE COVER LH |
![]() |
Disengage the 3 claws.
Disengage the clip and remove the rear seat leg side cover.
| 19. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function) |
Pull down the adjuster's lock piece to release the lock as shown in the illustration.

![]() |
Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.
Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.
Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.
| 20. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
![]() |
Remove the 3 bolts on the rear side of the seat.
![]() |
Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.
| 21. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side) |
![]() |
Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.
![]() |
Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.
| 22. REMOVE REAR SEAT TRACK BRACKET COVER RH |
![]() |
Disengage the 8 claws and remove the 2 rear seat track bracket covers.
| 23. REMOVE REAR OUTER TRACK BRACKET COVER RH |
![]() |
Disengage the 5 claws and remove the rear outer track bracket cover.
| 24. REMOVE REAR INNER TRACK BRACKET COVER RH |
![]() |
Disengage the 4 claws and remove the rear inner track bracket cover.
| 25. REMOVE REAR SEAT LEG SIDE COVER RH |
![]() |
Disengage the 3 claws.
Disengage the clip and remove the rear seat leg side cover.
| 26. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function) |
| 27. REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
![]() |
Remove the 3 bolts on the rear side of the seat.
![]() |
Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.
| 28. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 8 claws and guide, and remove the front door scuff plate LH.
| 29. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the front door opening trim weatherstrip LH.
| 30. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.
| 31. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the rear door opening trim weatherstrip LH.
| 32. REMOVE LOWER CENTER PILLAR GARNISH LH |
![]() |
Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.
| 33. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor end of the front seat outer belt assembly.
| 34. REMOVE DECK BOARD ASSEMBLY |
![]() |
Remove the deck board assembly.
| 35. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 guides and remove the No. 3 deck board sub-assembly.
| 36. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 guides and remove the No. 2 deck board sub-assembly.
| 37. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover assembly.
| 38. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) |
![]() |
Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.
| 39. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) |
![]() |
Disengage the 2 clips and remove the rear seat side cover LH.
| 40. REMOVE DECK SIDE TRIM BOX LH |
![]() |
Remove the 2 deck side trim clips and clip.
Remove the deck side trim box LH as shown in the illustration.

| 41. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) |
![]() |
Disengage the 2 clips and remove the rear seat side cover RH.
| 42. REMOVE JACK CARRIER SUPPORT |
| 43. REMOVE JACK CARRIER CUSHION |
![]() |
Remove the jack carrier cushion.
| 44. REMOVE JACK ASSEMBLY |
![]() |
Remove the jack assembly.
| 45. REMOVE JACK CARRIER ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 46. REMOVE DECK SIDE TRIM BOX RH |
![]() |
Remove the 2 deck side trim clips and clip.
Remove the deck side trim box RH as shown in the illustration.

| 47. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) |
![]() |
Remove the 4 bolts and 4 nuts.
Remove the deck floor board assembly.
| 48. REMOVE REAR MAT |
| 49. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Disengage the 3 claws.
Remove the 2 nuts and the deck floor board assembly.
| 50. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) |
![]() |
Remove the 2 nuts and the deck floor box.
| 51. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Remove the bolt and rear No. 2 seat inner belt assembly.
| 52. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) |
![]() |
Remove the bolt and disconnect the rear seat lap type belt assembly LH.
| 53. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) |
| 54. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Remove the 4 bolts and the rear No. 2 seat assembly.
| 55. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.
| 56. REMOVE DECK SIDE TRIM COVER LH |
![]() |
Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.
| 57. REMOVE DECK SIDE TRIM LH |
![]() |
Remove the bolt.
![]() |
Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.
| 58. REMOVE SIDE TRIM COVER LH (w/o Rear Seat Entertainment System) |
![]() |
Disengage the 10 claws and remove the side trim cover LH.
| 59. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System) |
![]() |
Disengage the 4 claws.
![]() |
Disconnect each connector and remove the power outlet socket bezel.
| 60. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH |
![]() |
Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.
| 61. REMOVE REAR POWER POINT SOCKET ASSEMBLY |
Disconnect the connector.
![]() |
Disengage the claw and remove the rear power point socket assembly.
| 62. REMOVE REAR POWER OUTLET SOCKET COVER |
![]() |
Disengage the 2 claws and remove the rear power outlet socket cover.
| 63. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function) |
![]() |
Disengage the 10 claws and remove the rear deck trim cover.
| 64. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function) |
![]() |
Disengage the 5 claws and remove the reclining remote control bezel LH.
| 65. REMOVE ROPE HOOK ASSEMBLY (for LH Side) |
![]() |
for Front Side:
Using a screwdriver, disengage the 2 claws.
Remove the bolt and the rope hook assembly.
![]() |
for Rear Side:
Using a screwdriver, disengage the 2 claws.
Remove the bolt and rope hook assembly.
| 66. REMOVE NO. 2 DECK SIDE TRIM HOOK |
![]() |
Remove the screw and the No. 2 deck side trim hook.
| 67. REMOVE FRONT DECK SIDE TRIM COVER LH |
![]() |
Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.
| 68. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.
| 69. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
Remove the 3 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

| 70. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Remove the 2 screws.
Remove the fuel lid lock open lever sub-assembly as shown in the illustration.
| 71. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the fuel lid lock control cable sub-assembly.
![]() |
Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.
Disengage the 9 clamps and remove the fuel lid lock control cable sub-assembly.
