TURN SIGNAL FLASHER ASSEMBLY > INSTALLATION |
| 1. INSTALL TURN SIGNAL FLASHER ASSEMBLY |
Connect the connector.
![]() |
Engage the claw and install the turn signal flasher assembly.
| 2. INSTALL POWER STEERING ECU ASSEMBLY |
![]() |
Install the power steering ECU assembly with the 3 nuts.
![]() |
Check that the connector lever is at the fully unlocked position before installation.
![]() |
Connect the 4 connectors to the power steering ECU assembly.
Lightly pull on the connector and check that the connector does not disconnect.
| 3. CONNECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
![]() |
Connect the instrument panel junction block assembly with the 3 nuts.
| 4. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Pole Antenna Type) |
Engage the 5 claws.
Install the 2 bolts <D> and nut <H>.
Install the 2 clips.

Engage each clamp.
Install the 2 passenger airbag bolts <A>.
Install the bolt <E>.
Connect each connector and install the instrument panel safety pad assembly.

| 5. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Glass Antenna Type) |
Engage the 5 claws.
Install the 2 bolts <D> and nut <H>.
Install the 2 clips.

Engage each clamp.
Install the 2 passenger airbag bolts <A>.
Connect each connector and install the instrument panel safety pad assembly.

| 6. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Connect the connector.
| 7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
Connect the connector.
![]() |
Install the front No. 2 speaker assembly with the 2 bolts.
| 8. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.
| 9. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
| 10. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.
| 11. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish RH.
Engage the 3 guides and 2 clips, then install the front pillar garnish RH.
| 12. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| 13. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish LH.
Engage the 3 guides and 2 clips, then install the front pillar garnish LH.
| 14. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| 15. INSTALL ENGINE SWITCH (w/ Smart Key System) |
![]() |
Engage the 2 claws to install the switch.
Connect the switch connector.
| 16. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the claw and 2 guides.
Install the front No. 2 console box insert with the 3 screws <F> and clip.
| 17. INSTALL FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Engage the claw and 2 guides.
Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.
| 18. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System) |
![]() |
Engage the 6 claws.
![]() |
Install the console box assembly with the 4 bolts and 2 screws.
| 19. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System) |
![]() |
Engage the 6 claws.
Connect the connector.
![]() |
Install the console box assembly with the 4 bolts and 2 screws.
| 20. INSTALL LOWER REAR CONSOLE BOX |
Install the lower rear console box.
| 21. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System) |
![]() |
Install the No. 2 console box duct as shown in the illustration.
| 22. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.
| 23. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System) |
![]() |
Connect the hood lock control cable assembly.
Connect each connector.
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 24. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Connect the hood lock control cable assembly.
Connect each connector and the aspirator duct.
![]() |
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 25. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the claw and clip, install the cowl side trim sub-assembly LH.
Install the clip.
| 26. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the guide and the 8 claws, and install the front door scuff plate LH.
| 27. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector and clamp.
![]() |
Engage the 4 claws and 3 clips.
Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.
| 28. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.
| 29. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 30. INSTALL FRONT DOOR SCUFF PLATE RH |
| 31. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System) |
Connect each connector.
![]() |
Engage the 4 clips.
![]() |
Install the radio receiver assembly with bracket with the 4 bolts.
| 32. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) |
Connect each connector.
![]() |
Engage the 4 clips.
![]() |
Install the navigation receiver assembly with bracket with the 4 bolts.
| 33. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System) |
Connect the connector.
![]() |
Engage the 4 clips and install the heater control and accessory assembly.
| 34. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) |
Connect the connector.
![]() |
Engage the 4 clips and install the air conditioning control assembly.
| 35. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Key System) |
![]() |
Apply protective tape to the areas shown in the illustration.
Connect each connector.
Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
| 36. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Key System) |
![]() |
Apply protective tape to the areas shown in the illustration.
Connect each connector.
Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
| 37. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.
| 38. INSTALL COMBINATION METER ASSEMBLY |
Connect the connector.
![]() |
Install the combination meter assembly with the 4 screws <F>.
| 39. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.
| 40. POSITION FRONT WHEELS STRAIGHT AHEAD |
| 41. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 42. INSTALL STEERING COLUMN COVER |
![]() |
Engage the claw to install the upper steering column cover.
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 2 screws.
| 43. ADJUST SPIRAL CABLE SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Rotate the spiral cable counterclockwise slowly by hand until it stops.
![]() |
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
| 44. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 45. INSPECT STEERING WHEEL CENTER POINT |
| 46. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Support the steering pad with one hand as shown in the illustration.
![]() |
Connect the 2 airbag connectors to the steering pad.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
![]() |
Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
| 47. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Install the lower No. 2 steering wheel cover with the claw.
| 48. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Install the lower No. 3 steering wheel cover with the claw.
| 49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 50. INSPECT STEERING PAD |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 51. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).