REAR DOOR BLACK OUT TAPE > REMOVAL |
| 1. DISCONNECT NEGATIVE BATTERY TERMINAL |
| 2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.
| 3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.
Disconnect the connector.
| 4. REMOVE DOOR ASSIST GRIP COVER |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.
| 5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the 3 screws.
![]() |
Using a clip remover, disengage the 9 clips.
Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.
![]() |
Disengage the 2 clamps.
Disconnect the front door lock remote control cable and rear door inside locking cable.
| 6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Remove the rear door inner glass weatherstrip from the rear door panel.
| 7. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector.
Remove the rear door service hole cover.
| 8. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
![]() |
Remove the rear door vent seal.
![]() |
Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.
| 10. REMOVE REAR DOOR QUARTER WINDOW GLASS |
![]() |
Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
Remove the 3 bolts.
Remove the rear door window regulator sub-assembly and the rear power window regulator motor assembly as a unit.
Remove the temporary bolt from the rear door window regulator sub-assembly.
| 13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Put protective tape around the rear door belt moulding assembly.
![]() |
Disengage the 6 claws and remove the rear door belt moulding assembly.
| 14. REMOVE REAR DOOR FRAME GARNISH |
![]() |
Disengage the clip and remove the rear door frame garnish.
| 15. REMOVE REAR DOOR WEATHERSTRIP |
![]() |
Remove the upper part of the rear door weatherstrip to the extent that allows removal of the black out tape.
| 16. REMOVE NO. 3 BLACK OUT TAPE |
Using a heat light, heat the No. 3 black out tape and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an end of the No. 3 black out tape and pull it parallel to the vehicle body to pull it off.
| 17. REMOVE NO. 2 BLACK OUT TAPE |
Using a heat light, heat the No. 2 black out tape and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an end of the No. 2 black out tape and pull it parallel to the vehicle body to pull it off.
| 18. REMOVE INNER UPPER BLACK OUT REAR DOOR TAPE |
Using a heat light, heat the inner upper black out rear door tape and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an end of the inner upper black out rear door tape and pull it parallel to the vehicle body to pull it off.
| 19. REMOVE INNER FRONT BLACK OUT REAR DOOR TAPE |
Using a heat light, heat the inner front black out rear door tape and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an end of the inner front black out rear door tape and pull it parallel to the vehicle body to pull it off.
| 20. REMOVE INNER REAR BLACK OUT REAR DOOR TAPE |
Using a heat light, heat the inner rear black out rear door tape and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an end of the inner rear black out rear door tape and pull it parallel to the vehicle body to pull it off.