Home › BODY › SEAT › FRONT SEATBACK HEATER (for Manual Seat Type RH Side)

FRONT SEATBACK HEATER (for Manual Seat Type RH Side) > INSTALLATION

for Preparation Click here



1. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B173750E01
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 7 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



2. INSTALL FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.



    B172866
  1. Engage the 4 claws and install the 2 front seat headrest supports.



    B176002
  1. Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B176001
  1. Engage the hooks.



    B176014E01
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B176015E01
  1. Using hog ring pliers, install the front seatback cover with pad with 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. Connect the seat heater connector.



3. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B170899
  1. Engage the guide as shown in the illustration.



    B170897
  1. Engage the claw.

  1. Install the front seat cushion inner shield with the screw.



4. INSTALL FRONT SEAT INNER BELT ASSEMBLY

HINT:
Use the same procedure for the RH side and the LH side .



5. INSTALL FRONT SEAT CUSHION SHIELD


    B170888
  1. Engage the 2 guides.

  1. Engage the claw.



    B170913
  1. Install the front seat cushion shield with the 2 screws.



    B180386
  1. Engage the 2 hooks.



6. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B170887
  1. Engage the claw and install the reclining adjuster release handle.



7. INSTALL FRONT SEAT ASSEMBLY

HINT:
Use the same procedure for the RH side and the LH side .



8. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK

HINT:
Use the same procedure for the RH side and the LH side .



9. INSTALL REAR INNER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side .



10. INSTALL REAR OUTER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side .



11. INSTALL FRONT INNER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side .



12. INSTALL FRONT OUTER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side .



13. INSTALL FRONT SEAT HEADREST ASSEMBLY

HINT:
Use the same procedure for the RH side and the LH side .



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When reconnected the cable, some systems need to be initialized (Click here).



15. INSPECT FRONT SEAT ASSEMBLY
  1. Check the seat heater operation.

    1. Turn the ignition switch on (IG).

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.



16. INSPECT SRS WARNING LIGHT