Home › ENGINE › 3MZ-FE COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A078535
  1. Install a new gasket and the water pump with the 3 bolts and 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



2. INSTALL NO. 2 TIMING BELT IDLER SUB-ASSEMBLY

Torque:
43 N*m{ 438 kgf*cm , 32 ft.*lbf }



3. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
  1. Using a 10 mm socket hexagon wrench, install the plate washer and No. 1 timing belt idler with the pivot bolt.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



4. INSTALL NO. 3 TIMING BELT COVER
  1. Visually check for cracks and breaks on the gasket of the timing belt cover.

    HINT:
    If a trace of water is found in the visual check, repair it with seal packing when the crack length is within 2 to 3 cm (0.79 to 1.18 in.). Replace the gasket when the crack length is 3 to 4 cm (1.18 to 1.57 in.) and more.



    A078748E05
  1. If the timing belt cover gasket is needed to repair, follow the procedure below.

    1. Repair the cracks and breaks by applying the seal packing to the damaged area.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      NOTICE:
      When applying the seal packing, apply it as wide and high as possible to fill the surface area of the gasket.



  1. If the timing belt cover gasket is needed to replace, follow the procedure below.

    1. Using a screwdriver and gasket scraper, remove the remaining gasket.

      NOTICE:
      Do not damage the timing belt cover.



    2. A078749E10
    3. Remove the backing paper from a new gasket, and affix the gasket along the groove of the timing belt cover as shown in the illustration.

      NOTICE:
      1. Affix the gasket in the center of the groove.
      2. At the corners, try to keep the gasket thickness uniform.

      Gasket
      D
      E
      F
      G
      Length
      335 mm
      (13.19 in.)
      180 mm
      (7.09 in.)
      133 mm
      (5.24 in.)
      72 mm
      (2.83 in.)

    4. If there is a gap on the joint of the gasket, apply seal packing to close the gap.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      NOTICE:
      When applying the seal packing, apply it as wide and high as possible to fill the surface area of the gasket.



    A109778
  1. Install the timing belt cover with the 6 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



5. INSTALL CAMSHAFT TIMING PULLEY


    A078750E01
  1. Paying attention to the direction of the belt guide, install the camshaft timing pulley and tighten the bolt temporarily.

    HINT:
    1. Face the belt guide of the RH timing pulley toward the front of the engine.
    2. Face the belt guide of the LH timing pulley toward the rear of the engine.



    A109742E01
  1. Using SST, tighten the RH pulley bolt.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    125 N*m{ 1275 kgf*cm , 92 ft.*lbf }



    A109743E01
  1. Using SST, tighten the LH pulley bolt.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    125 N*m{ 1275 kgf*cm , 92 ft.*lbf }



6. INSPECT TIMING BELT

NOTICE:
  1. Do not bend, twist or turn the timing belt inside out.
  2. Do not allow the timing belt to come into contact with oil, water or steam.
  3. Do not utilize timing belt tension when installing or removing the mounting bolt of the camshaft timing pulley.
Check the belt for any defects, as shown in the illustration. Also, check the points below.



    EM03336E01
  1. If there is premature parting:

    1. Check for proper installation.

  1. If the belt teeth are cracked or damaged, check if either camshaft is locked.

  1. If there is noticeable wear or cracks on the belt face, check if there are nicks on the side of the idler pulley lock and water pump.

  1. If there is wear or damage to only one side of the belt, check the belt guide and the alignment of each pulley.

  1. If there is noticeable wear on the belt teeth:

    1. Check the timing cover for damage.
    2. Check for foreign objects on the pulley teeth. If there is any trouble in the belt condition, replace the timing belt.



7. INSTALL TIMING BELT

HINT:
Click here