Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DTC    P0021    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0022    Camshaft Position "A" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM (included in the hybrid vehicle control ECU), oil control valve and VVT controller. The ECM sends a target duty-cycle control signal to the oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as intake air volume, throttle valve position and engine coolant temperature. The ECM controls oil control valve, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Advanced cam timing:
With warm engine and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (1 trip detection logic):
  1. Difference between target and actual intake valve timing more than 5°CA (Crankshaft Angle) for 9.5 seconds
  2. Current intake valve timing fixed (timing changes less than 5° CA in 5 seconds)
  3. Variations in VVT controller timing more than 19°CA of maximum delayed timing (advance)
  1. Valve timing
  2. Oil control valve (bank 1, 2)
  3. Oil control valve filter (bank 1, 2)
  4. Intake camshaft (bank 1, 2) timing gear assembly
  5. Hybrid Vehicle Control ECU
P0012
P0022
Retarded cam timing:
With warm engine and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (2 trip detection logic):
  1. Difference between target and actual intake valve timing more than 5°CA (Crankshaft Angle) for 9.5 seconds
  2. Current intake valve timing fixed (timing changes less than 5° CA in 5 seconds)
  3. Variations in VVT controller timing 19°CA or less of maximum delayed timing (retard)
  1. Valve timing
  2. Oil control valve (bank 1, 2)
  3. Oil control valve filter (bank 1, 2)
  4. Intake camshaft (bank 1, 2) timing gear assembly
  5. Hybrid Vehicle Control ECU

MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the oil control valve (OCV) and the VVT controller. The ECM sends a target duty-cycle control signal to the oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timing is large, and changes in actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and sets a DTC.
  1. Example
  1. A DTC is set when the following conditions (a), (b) and (c) are met:
    1. The difference between the target and actual intake valve timing is more than 5° CA (Crankshaft Angle) and the condition continues for more than 9.5 seconds.
    2. It takes 5 seconds or more to change the valve timing by 5° CA.
    3. After above conditions (a) and (b) are met, the oil control valve is forcibly activated 70 times or more.
  2. DTCs P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  3. DTCs P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  4. These DTCs indicate that the VVT controller cannot operate properly due to oil control valve malfunctions or the presence of foreign objects in the oil control valve.
  5. The monitor will not run unless the following conditions are met:
    1. The engine is warm (the engine coolant temperature is 75°C (167°F) or more).
    2. The vehicle has been driven at more than 47 mph (75 km/h) for 3 minutes.
    3. The engine has idled for 3 minutes.

MONITOR STRATEGY


Related DTCs
P0011: Advanced camshaft timing (bank 1)
P0012: Retard camshaft timing (bank 1)
P0021: Advanced camshaft timing (bank 2)
P0022: Retard camshaft timing (bank 2)
Required sensors / components (Main)
VVT oil control valve and camshaft timing gear
Required sensors / components (Related)
Crankshaft position sensor, camshaft position sensor and engine coolant temperature sensor
Frequency of operation
Once per driving cycle
Duration
Within 10 seconds
MIL operation
Advanced camshaft timing (bank 1): Immediately
Advanced camshaft timing (bank 2): Immediately
Retarded camshaft timing (bank 1): 2 driving cycles
Retarded camshaft timing (bank 2): 2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0010, P0020 (VVT oil control valve bank 1, 2)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, O0117, P0118 (Engine coolant temperature sensor)
P0125 (insufficient engine coolant temperature for closed loop)
P0335 (Crankshaft position sensor)
Battery voltage
11 V or more
Engine RPM
500 to 4000 rpm
Engine coolant temperature
75°C (167°F) to 100°C (212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced camshaft timing: 
All of the following conditions are met
-
Deviation of valve timing
More than 5°CA
Valve timing
No change at advanced valve timing

Retard camshaft timing: 
All of the following conditions are met
-
Deviation of valve timing
More than 5°CA
Valve timing
No change at retarded valve timing
If the difference between the target and actual camshaft timing is greater than the specified value, the ECM (included in the hybrid vehicle control ECU) operates the VVT actuator.
Then, the ECM monitors changes in the camshaft timing for 5 seconds.

WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE


HINT:

Abnormal Bank
Advanced Timing Over
(Valve Timing is out of Specified Range)
Retarded Timing Over
(Valve Timing is out of Specified Range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
  1. If DTC P0011 or P0012 is output, check the right bank VVT system (bank 1).
  2. Bank 1 refers to the bank that includes cylinder No. 1.
  3. If DTC P0021 or P0022 is output, check the left bank VVT system (bank 2).
  4. Bank 2 refers to the bank that does not include cylinder No. 1.
  5. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menu items: Powertrain / Engine and ECT / Monitor.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0011, P0012, P0021 or P0022
    A
    P0011, P0012, P0021 or P0022 and other DTCs
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Select, the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the oil control valve using the Techstream.

    OK:

    Techstream Operation
    Specified Condition
    Oil control valve OFF
    Normal engine speed
    Oil control valve ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Clear the DTCs.

  1. Start the engine and warm it up.

  1. Switch the ECM (included in the hybrid vehicle control ECU) from normal mode to check mode using the Techstream.

  1. Drive the vehicle for more than 10 minutes.

  1. Read the DTCs using the tester.

    OK:
    No DTC output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING BELT)


    A109150
  1. Remove the cylinder head covers RH and LH.

  1. Turn the crankshaft pulley, and align its groove with timing mark "0" of the timing belt cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the No. 3 timing belt cover as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    The timing marks on the camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head covers.



NG
ADJUST VALVE TIMING
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A095415E03
  1. Remove the oil control valve.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω



    A097066E01
  1. Apply positive battery voltage to terminal 1 and connect the negative battery terminal to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the oil control valve.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter.

    OK:
    The filter is not clogged.



NG
REPLACE OIL CONTROL VALVE FILTER
OK


7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).


NEXT


8.READ VALUE USING TECHSTREAM (CHECK IF DTC OUTPUT RECURS)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Clear the DTCs.

  1. Start the engine and warm up.

  1. Switch the ECM (included in the hybrid vehicle control ECU) from normal mode to the check mode using the Techstream.

  1. Drive the vehicle for more than 10 minutes.

  1. Read the output DTCs using the Techstream.

    Standard:
    No DTC output.

    HINT:
    DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some parts of the system. These codes will remain set even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

SYSTEM OK