Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

DTC    P0020    Camshaft Position "A" Actuator Circuit (Bank 2)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM (included in the hybrid vehicle control ECU), Oil Control Valve and VVT controller. The ECM sends a target duty-cycle control signal to the oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as intake air volume, throttle valve position and engine coolant temperature. The ECM controls the oil control valve, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improves, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A172461E01


DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in oil control valve (bank 1) circuit
(1 trip detection logic)
  1. Open or short in oil control valve (bank 1) circuit
  2. Oil control valve (bank 1)
  3. Hybrid vehicle control ECU
P0020
Open or short in oil control valve (bank 2) circuit
(1 trip detection logic)
  1. Open or short in oil control valve (bank 2) circuit
  2. Oil control valve (bank 2)
  3. Hybrid vehicle control ECU

MONITOR DESCRIPTION

After the ECM (included in the hybrid vehicle control ECU) sends the "target" duty-cycle signal to the oil control valve, the ECM monitors the oil control valve current to establish an "actual" duty-cycle. The ECM detects a malfunction and sets a DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.

MONITOR STRATEGY


Related DTCs
P0010: VVT oil control valve (bank 1) open/short
P0020: VVT oil control valve (bank 2) open/short
Required sensors / components (Main)
VVT oil control valve (Variable Valve Timing Oil Control Valve)
Required sensors / components (Related)
-
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
All of the following conditions are met
-
Starter
OFF
Power switch
ON
Time after power switch off to on
0.5 seconds or more
Either of the following conditions is met
-
A. All of the following conditions are met
-
Battery voltage
11 V or more and less than 13 V
Target duty ratio
Less than 70%
Current cut status
Not cut
B. All of the following conditions are met
-
Battery voltage
13 V or more
Target duty ratio
Less than 80%
Current cut status
Not cut

TYPICAL MALFUNCTION THRESHOLDS


VVT oil control valve condition
No operation record

COMPONENT OPERATING RANGE


VVT oil control valve condition
Operation record

WIRING DIAGRAM


A182709E01


INSPECTION PROCEDURE

HINT:
  1. If DTC P0010 is output, check the right bank VVT system.
  2. Bank 1 refers to the bank that includes cylinder No. 1.
  3. If DTC P0020 is output, check the left bank VVT system.
  4. Bank 2 refers to the bank that does not include cylinder No. 1.
  5. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.PERFORM ACTIVE TEST USING CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the oil control valve using the Techstream.

    OK:

    Techstream Operation
    Specified Condition
    Oil Control Valve OFF
    Normal engine speed
    Oil Control Valve ON
    Engine idles roughly or stalls (soon after oil control valve switched from OFF to ON)



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A095415E03
  1. Disconnect the oil control valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Reconnect the oil control valve connector.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3.INSPECT HARNESS AND CONNECTOR (OIL CONTROL VALVE - HYBRID VEHICLE CONTROL ECU)


    A110896E07
  1. Disconnect the oil control valve connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B24-1 - B3-16 (OC1+)
    Always
    Below 1 Ω
    B24-2 - B3-15 (OC1-)
    Always
    Below 1 Ω
    B25-1 - B3-14 (OC2+)
    Always
    Below 1 Ω
    B25-2 - B3-13 (OC2-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B24-1 (OCV) or B3-16 (OC1+) - Body ground
    Always
    10 kΩ or higher
    B24-2 (OCV) or B3-15 (OC1-) - Body ground
    Always
    10 kΩ or higher
    B25-1 (OCV) or B3-14 (OC2+) - Body ground
    Always
    10 kΩ or higher
    B25-2 (OCV) or B3-13 (OC2-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the oil control valve connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)