Home › HYBRID SYSTEM ยท P310 › HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER POSITION SENSOR

SHIFT LEVER POSITION SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL SHIFT LEVER POSITION SENSOR
  1. Install the shift lever position sensor to the manual valve shaft.



    C108750
  1. Temporarily install the 2 bolts.



    C110903E02
  1. Place a new lock plate and tighten the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever.



    C113927E01
  1. Turn the lever clockwise until it stops, then turn it counterclockwise 2 notches.

  1. Remove the control shaft lever.



    C175439E01
  1. Align the protruding part with the neutral basic line.

    NOTICE:
    There is play on the nut stopper side (protruding part). Align the center point of the range of the play with the neutral basic line.



    C108753E01
  1. Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    C110901E01
  1. Using a screwdriver, stake the nut with the lock plate.



    C108748E02
  1. Install the control shaft lever, washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Move the shift lever to the N position.

  1. Install a new clip to the control bracket.



    C173145E01
  1. Install the control cable to the control bracket.

    NOTICE:
    1. Make sure that the A claws on the clip are securely fit into the bracket holes.
    2. Make sure that the cable is securely engaged by the B claws of the clip.



    C108747
  1. Connect the shift lever position sensor connector.

  1. Move the control shaft lever to the N position.



    C108745
  1. Temporarily install the control cable to the control shaft lever with the nut.



    C113929E02
  1. Lightly pull down the control cable end.

    NOTICE:
    Do not pull the control cable end excessively.

  1. Release your hand from the control cable end and then fully tighten the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSTALL OIL COOLER TUBE SUB-ASSEMBLY


    C172977
  1. Install the clamp to the tube support bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }



    C113019
  1. Using a union nut wrench 17 mm and a wrench, tighten the 2 new oil cooler tubes.

    Torque:
    without Union nut wrench:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }
    with Union nut wrench:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 180 mm (7.09 in.).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.



    C113018
  1. Install the tube support bracket to the control cable bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the 2 oil cooler hoses to the oil cooler tubes.



4. ADD AND INSPECT HYBRID TRANSAXLE FLUID
  1. Add transaxle fluid.



    C173144E01
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Keep the fluid temperature at 5°C (41°F) or higher.
    2. Stop the vehicle on a flat road.
    3. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Using a socket hexagon wrench 10 mm, temporarily tighten the filler plug and gasket.

  1. Enter 2WD inspection mode (Click here).

  1. After waiting for 1 minute or more, stop the engine.

  1. Using a socket hexagon wrench 10 mm, remove the filler plug and gasket.

  1. Add transaxle fluid.



    C173144E01
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Keep the fluid temperature at 5°C (41°F) or higher.
    2. Stop the vehicle on a flat road.
    3. Recheck the transaxle fluid level after driving when exchanging fluid.
    4. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Check for leaks if the fluid level is low.

  1. Using a socket hexagon wrench 10 mm, install the filler plug, and a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



5. INSPECT SHIFT LEVER POSITION
  1. Apply the parking brake.

  1. Lock the wheels with chocks to secure the vehicle.

  1. Turn the power switch on (READY).

  1. Move the shift lever to the D position and release the brake pedal.

    NOTICE:
    Be sure to apply the parking brake and lock the wheels with chocks to secure the vehicle.

  1. Slowly move the shift lever to the N position and measure moving distance (a) of the shift lever from the original point to the gear activation point.

    NOTICE:
    Be sure to move the shift lever slowly.

  1. Move the shift lever to the R position and release the brake pedal.

    NOTICE:
    Be sure to apply the parking brake and lock the wheels with chocks to secure the vehicle.

  1. Slowly move the shift lever to the N position and measure moving distance (b) of the shift lever from the original point to the vehicle activation point.

    NOTICE:
    Be sure to move the shift lever slowly.



  1. Check that moving distances (a) and (b) shown in the illustration are almost the same.


    C172354E01

    HINT:
    1. If moving distances (a) and (b) are almost the same, adjustment of the shift lever position is not necessary.
    2. If moving distance (a) is shorter than (b), perform adjustment of the shift lever position [*1].
    3. If moving distance (b) is shorter than (a), perform adjustment of the shift lever position [*2].



6. ADJUST SHIFT LEVER POSITION


  1. If moving distance (a) is shorter than (b) [*1]:


    C172354E01

    HINT:
    If the shift lever is moved from the R to the N position, the moving distance of the shift lever from the original point to the gear activation point becomes longer.


    1. Move the shift lever to the N position.



    2. C108753
    3. Loosen the 2 bolts.



    4. C115287
    5. Slightly turn the shift lever position sensor counterclockwise.



    6. C108753E02
    7. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    8. Recheck the shift lever position.



  1. If moving distance (b) is shorter than (a) [*2]:


    C172354E01

    HINT:
    If the shift lever is moved from the D to the N position, the moving distance of the shift lever from the original point to the gear activation point becomes longer.


    1. Move the shift lever to the N position.



    2. C108753
    3. Loosen the 2 bolts.



    4. C115288
    5. Slightly turn the shift lever position sensor clockwise.



    6. C108753E02
    7. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    8. Recheck the shift lever position.



7. INSPECT SHIFT LEVER OPERATION
  1. While moving the shift lever from the N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

  1. Turn the power switch on (READY), and check the following:

    1. When the shift lever is moved to the D position, the vehicle moves forward.

    2. When the shift lever is moved to the R position, the buzzer sounds and the vehicle moves in reverse.

      NOTICE:
      The vehicle should not move when the shift position indicator is off.



8. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.