Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2799-542    Engine Immobiliser System Malfunction

DTC    B2799-790    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output if one of the following occurs: 1) the hybrid vehicle control ECU detects errors in its own communication with the ID code box (immobiliser code box); 2) the hybrid vehicle control ECU detects an error in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and hybrid vehicle control ECU is different and a hybrid system start is attempted. Before troubleshooting this DTC, make sure no certification ECU DTCs are present. If present, troubleshoot the certification ECU (smart key ECU assembly) DTCs first.

DTC No.
DTC Detection Condition
Trouble Area
B2799-542
B2799-790
One of following conditions is met:
  1. Error in communication between hybrid vehicle control ECU and ID code box (immobiliser code ECU)
  2. Error in communication lines
  3. Communication ID is different between ID code box (immobiliser code ECU) and hybrid vehicle control ECU during communication
  1. Wire harness or connector
  2. Hybrid vehicle control ECU
  3. ID code box (immobiliser code ECU)

WIRING DIAGRAM


B151007E16


INSPECTION PROCEDURE

NOTICE:
  1. If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID (Click here).
  2. If the hybrid vehicle control ECU is replaced, register the ECU communication ID (Click here).

1.CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs.

    OK:
    B2799 output does not recur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.RE-REGISTER ECU COMMUNICATION ID
  1. Re-register the ECU communication ID (Click here).


NEXT


3.CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs.

    OK:
    B2799 output does not recur.



NG
Go to step 4
OK

END (ECU COMMUNICATION ID IS DEFECTIVE) 

4.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the hybrid vehicle control ECU and the ID code box (immobiliser code ECU).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


5.CHECK HARNESS AND CONNECTOR (ID CODE BOX - HYBRID VEHICLE CONTROL ECU)


  1. Disconnect the ID code box (immobiliser code ECU) and hybrid vehicle control ECU connectors.


    B178880E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D31-5 (EFII) - D35-28 (IMO)
    Always
    Below 1 Ω
    D31-6 (EFIO) - D35-22 (IMI)
    Always
    Below 1 Ω
    D31-5 (EFII) - Body ground
    Always
    10 kΩ or higher
    D31-6 (EFIO) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D31-5 (EFII) - Body ground
    Power switch on (IG)
    Below 1 V
    D31-6 (EFIO) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE HYBRID VEHICLE CONTROL ECU
  1. Replace the hybrid vehicle control ECU (Click here).


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Re-register the ECU communication ID (Click here).


NEXT


8.CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs.

    OK:
    B2799 output does not recur.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU) (Click here)
OK

END (HYBRID VEHICLE CONTROL ECU IS DEFECTIVE)