POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder |

| 1.INSPECT FUSE (DOOR1) |
Remove the DOOR1 fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DOOR1 fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK DOOR LOCK OPERATION |
| Result | Proceed to |
| Doors cannot be locked through driver side door key cylinder. | A |
| Doors cannot be locked through master switch. | B |
|
| ||||
| B | |
| 3.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus:
Body Electrical / Main Body / Data List.
Select Door Lock SW-Lock or Door Lock SW-Unlock in the Data List and read the Techstream display.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Lock SW-Lock | Door manual lock switch signal/ON or OFF | ON: While door control switch on power window regulator master switch is pushed to LOCK OFF: Door control switch on power window regulator master switch is not pushed | - |
| Door Lock SW-Unlock | Door manual unlock switch signal/ON or OFF | ON: While door control switch on power window regulator master switch is pushed to UNLOCK OFF: Door control switch on power window regulator master switch is not pushed | - |
|
| ||||
| OK | ||
| ||
| 4.INSPECT POWER WINDOW MASTER SWITCH |
Remove the power window master switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Locked | Below 1 Ω |
| 1 - 2 1 - 9 | OFF (Free) | 10 kΩ or higher |
| 1 - 9 | Unlocked | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH CIRCUIT) |
![]() |
Disconnect the instrument panel junction block connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-2 (L) - 1K-15 | Always | Below 1 Ω |
| M1-9 (UL) - 1K-12 | Always | Below 1 Ω |
| M1-1 (E) - Body ground | Always | Below 1 Ω |
| M1-2 (L) - Body ground | Always | 10 kΩ or higher |
| M1-9 (UL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.READ VALUE USING TECHSTREAM (DOOR KEY LINKED LOCK AND UNLOCK SWITCH) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus:
Body Electrical / Main Body / Data List.
Select Door Key SW-Lock or Door Key SW-Unlock in the Data List and read the Techstream display.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Key SW-Lock | Door key linked lock switch signal/ON or OFF | ON: While driver side door key cylinder is turned to LOCK OFF: Driver side door key cylinder is not turned | - |
| Door Key SW-Unlock | Door key linked unlock switch signal/ON or OFF | ON: While driver side door key cylinder is turned to UNLOCK OFF: Driver side door key cylinder is not turned | - |
|
| ||||
| OK | ||
| ||
| 7.INSPECT FRONT DOOR LOCK ASSEMBLY (FOR DRIVER SIDE) |
![]() |
Remove the front door lock assembly LH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 7 - 9 | ON (Door lock set to LOCK) | Below 1 Ω |
| 7 - 9 7 - 10 | OFF (Free) | 10 kΩ or higher |
| 7 - 10 | ON (Door lock set to UNLOCK) | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (DOOR KEY LINKED LOCK UNLOCK SWITCH CIRCUIT) |
Disconnect the main body ECU (instrument panel junction block) and instrument panel junction block connectors.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H6-9 (L) - 1K-16 | Always | Below 1 Ω |
| H6-10 (UL) - D8-10 (UL3) | Always | Below 1 Ω |
| H6-7 (E) - Body ground | Always | Below 1 Ω |
| H6-9 (L) - Body ground | Always | 10 kΩ or higher |
| H6-10 (UL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||