Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL REAR AIRBAG SENSOR
  1. Check that the power switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165114
  1. Install the rear airbag sensor with the bolt and pin.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
    3. Make sure that the pin is securely inserted into the body hole.
    4. Tighten the bolt while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

  1. Check that there are no loose parts after installing the rear airbag sensor.

  1. Connect the connector to the rear airbag sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly LH with the 2 bolts.


    B173613



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly RH with the 3 bolts.


    B173622



4. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    B170934E01
  1. Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.



5. INSTALL FRONT DECK SIDE TRIM COVER


    B175145
  1. Engage the 4 claws and install the 2 front deck side trim covers LH.



6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.



7. INSTALL NO. 2 DECK SIDE TRIM HOOK (for LH Side)


    B173612
  1. Install the No. 2 deck side trim hook with the screw.



8. INSTALL ROPE HOOK ASSEMBLY


    B173599
  1. for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



    B173601
  1. for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



9. INSTALL REAR DECK TRIM COVER (for LH Side without Remote Folding Function)


    B173602
  1. Engage the 10 claws and install the rear deck trim cover.



10. INSTALL RECLINING REMOTE CONTROL BEZEL (for LH Side with Remote Folding Function)


    B173603
  1. Engage the 5 claws and install the reclining remote control bezel lever LH.



11. INSTALL REAR POWER OUTLET SOCKET COVER (for LH Side)


    E151328
  1. Engage the 2 claws and install the rear power outlet socket cover.



12. INSTALL REAR POWER POINT SOCKET ASSEMBLY (for LH Side)


    E151490
  1. Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.



13. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)


    B173619
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.



14. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)


    B175146
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.



15. INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)


    B173610
  1. Engage the 4 claws, and install the side trim cover RH.



16. INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)
  1. Connect the connector.



    E150364
  1. Engage the 4 claws and install the rear room temperature sensor.



17. INSTALL SIDE TRIM COVER LH (for LH Side without Rear Seat Entertainment System)


    B173597
  1. Engage the 10 claws and install the side trim cover LH.



18. INSTALL POWER OUTLET SOCKET BEZEL (for LH Side with Rear Seat Entertainment System)


    B173681
  1. Connect each connector.



    B173680
  1. Engage the 4 claws and install the power outlet socket bezel.



19. INSTALL DECK SIDE TRIM


    B173624
  1. Engage the 3 guides and 4 claws as shown in the illustration.



    B173596
  1. Install the deck side trim LH with the bolt.



20. INSTALL DECK SIDE TRIM COVER


    B175144
  1. Engage the 2 claws and install the deck side trim cover LH.



21. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)


    B173615
  1. Engage the guide and the 8 claws, and install the rear seat side garnish cap.



22. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)


    B173617
  1. Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.



23. INSTALL REAR FLOOR FINISH PLATE


    B173609
  1. Engage the 4 clips and the 4 claws, and install the rear floor finish plate.



24. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B173781
  1. Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



25. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY (w/ Rear No. 2 Seat)
for LH side: .
for RH side: .


26. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.



27. INSTALL NO. 1 DECK BOARD (w/o Rear No. 2 Seat)


    B178559
  1. Engage the 5 clips and install the rear floor board spacer to the No. 1 deck board.



28. INSTALL NO. 1 DECK BOARD (w/ Rear No. 2 Seat)


    B178557
  1. Engage the 5 clips and install the deck floor box to the No. 1 deck board.



29. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Install the rear deck floor box with the 2 nuts.



30. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Install the deck floor board assembly with the 4 nuts and 4 bolts.



31. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.



32. INSTALL REAR MAT


    B173249
  1. Install the rear mat.



33. INSTALL DECK SIDE TRIM BOX RH


  1. Install the deck side trim box RH as shown in the illustration.


    B178553



    B173247E01
  1. Install the 2 deck side trim clip and the clips.



34. INSTALL JACK CARRIER ASSEMBLY


    B178549
  1. Engage the 3 claws, and install the jack carrier assembly.



35. INSTALL JACK ASSEMBLY


    B173245
  1. Install the jack assembly.



36. INSTALL JACK CARRIER CUSHION


    B178550
  1. Install the jack carrier cushion.



37. INSTALL JACK CARRIER SUPPORT


38. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    B173608
  1. Engage the 2 clips and install the rear seat side cover RH.



39. INSTALL DECK SIDE TRIM BOX LH


  1. Install the deck side trim box LH as shown in the illustration.


    B178555



    B173243E01
  1. Install the 2 deck side trim clip and the clips.



40. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Engage the 2 clips and install the rear seat side cover LH.



41. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    B175152
  1. Engage the 3 guides and 3 clips and install the rear No. 1 floor board.



42. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



43. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Engage the 2 guides and install the No. 2 deck board sub-assembly.



44. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Engage the 2 guides and install the No. 3 deck board sub-assembly.



45. INSTALL DECK BOARD ASSEMBLY


    B173240
  1. Install the deck board assembly.



46. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    B173233E01
  1. Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



47. INSTALL REAR DOOR SCUFF PLATE


    B173228
  1. Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.



48. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



49. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).