Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CENTER AIRBAG SENSOR ASSEMBLY

CENTER AIRBAG SENSOR ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B184680E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.



4. REMOVE FRONT DOOR SCUFF PLATE LH


    B173224
  1. Disengage the 8 claws and guide, and remove the front door scuff plate LH.



5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.



6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B173021
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.



    B173009
  1. Disconnect each connector and the aspirator duct.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.



7. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side .



8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side .



9. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B172999
  1. Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.



10. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B168370
  1. Remove the 2 bolts <B> and 3 screws <E>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.



11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.



12. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    B173012
  1. Remove the No. 2 console box duct as shown in the illustration.



13. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.



14. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    B173628
  1. Remove the 4 bolts and 2 screws.



    B173629
  1. Disengage the 6 claws and remove the console box assembly.



15. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    B181135
  1. Remove the 4 bolts and 2 screws.



    B175149
  1. Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.



16. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    B168373
  1. Using a clip remover, remove the 2 clips.

  1. Remove the 3 screws <E>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.



17. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Using a clip remover, remove the clip.

  1. Remove the 3 screws <E>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.



18. REMOVE CENTER AIRBAG SENSOR ASSEMBLY


    C165110
  1. Disconnect the holder (with connectors).

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and center airbag sensor assembly.