STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft sub-assembly and the steering column assembly.
![]() |
Install a new bolt.
| 2. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Check that the 2 bushings are securely installed to the steering column assembly.
![]() |
Install the steering column assembly with the bolt and 2 nuts.
Connect the connectors and engage the wire harness clamps to the steering column assembly.
![]() |
Connect the connector to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
| 3. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.
![]() |
Install a new bolt.
![]() |
Install the steering intermediate shaft sub-assembly to the steering column hole shield.
![]() |
Tighten the bolt.
| 4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY |
![]() |
Engage the 2 claws to install the No. 1 air duct sub-assembly.
| 5. POSITION FRONT WHEELS STRAIGHT AHEAD |
| 6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 7. INSTALL STEERING COLUMN COVER |
![]() |
Engage the claw to install the upper steering column cover.
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 2 screws.
| 8. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
![]() |
Install the brake pedal support sub-assembly with the 4 nuts.
![]() |
Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.
![]() |
Connect the connector and engage the clamp.
| 9. INSTALL PUSH ROD PIN |
![]() |
Apply lithium soap base glycol grease to the push rod pin.
Install the push rod pin to connect the brake master cylinder push rod clevis and brake pedal sub-assembly as shown in the illustration.
Install a new clip to the push rod pin.
| 10. INSTALL BRAKE PEDAL RETURN SPRING |
![]() |
Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.
| 11. INSTALL STOP LIGHT SWITCH ASSEMBLY |
![]() |
Temporarily install the stop light switch assembly with the stop light switch lock nut.
![]() |
Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).
Tighten the stop light switch lock nut.
![]() |
Connect the connector.
| 12. INSPECT AND ADJUST BRAKE PEDAL HEIGHT |
Check the brake pedal height.
![]() |
Turn back the carpet.
Measure the shortest distance between the brake pedal surface and tibia pad.
Adjust the brake pedal height.
Disconnect the stop light switch connector.
Remove the stop light switch assembly.
Loosen the push rod clevis lock nut.
Adjust the brake pedal height by turning the push rod.
Tighten the push rod clevis lock nut.
Install and adjust the stop light switch .
Connect the stop light switch connector.
| 13. INSPECT BRAKE PEDAL FREE PLAY |
![]() |
Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.
| 14. INSPECT BRAKE PEDAL RESERVE DISTANCE |
![]() |
Release the parking brake lever.
With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.
| 15. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
Check that the power switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Install the DLC3 to the driver side knee airbag assembly with the 2 claws.
![]() |
Connect the connector to the driver side knee airbag assembly.
![]() |
Support the driver side knee airbag assembly with one hand as shown in the illustration.
![]() |
Temporarily install the driver side knee airbag assembly with the 2 hooks.
![]() |
Install the driver side knee airbag assembly with the 4 bolts.
| 16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Connect the hood lock control cable assembly.
Connect each connector and the aspirator duct.
![]() |
Engage the 3 claws and 10 clips.
Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
| 17. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the claw and clip, install the cowl side trim sub-assembly LH.
Install the clip.
| 18. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the guide and the 8 claws, and install the front door scuff plate LH.
| 19. ADJUST SPIRAL CABLE |
Check that the power switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Rotate the spiral cable counterclockwise slowly by hand until it stops.
![]() |
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
| 20. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 21. INSTALL STEERING PAD |
Check that the power switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Support the steering pad with one hand as shown in the illustration.
![]() |
Connect the 2 airbag connectors to the steering pad.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
![]() |
Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
| 22. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Install the lower No. 3 steering wheel cover with the claw.
| 23. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Install the lower No. 2 steering wheel cover with the claw.
| 24. INSTALL FRONT WHEEL LH |
| 25. INSPECT STEERING WHEEL CENTER POINT |
| 26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 27. INSPECT STEERING PAD |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 28. INSPECT SRS WARNING LIGHT |