Home › ENGINE › 3MZ-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY
  1. Install new grommets to each fuel injector.



    A112349E01
  1. Apply a light coat of spindle oil or gasoline to new O-rings, and install them to each fuel injector.



    A081139E03
  1. Apply a light coat of spindle oil or gasoline to the place where the fuel delivery pipe contacts the O-ring.

  1. Push the fuel injector while turning it back and forth to install it in the fuel delivery pipe.

    NOTICE:
    1. Be careful not to twist the O-ring.
    2. After installing the fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.



    A108731E01
  1. Install 6 new insulators (B) and the 4 No. 1 delivery pipe spacers (A) to the intake manifold.



    A108732
  1. Place the 2 fuel delivery pipes and the 6 fuel injectors together to the intake manifold.

    NOTICE:
    Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

  1. Temporarily install the 4 bolts which are used to attach the fuel delivery pipe to the intake manifold.

  1. Check that the fuel injectors rotate smoothly. If the fuel injectors do not rotate smoothly, the probable cause is incorrect installation of the O-ring. Replace with a new O-ring.

  1. Tighten the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A108729
  1. Connect the 6 fuel injector connectors.



2. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY


    A082435E02
  1. Install 2 new gaskets and the No. 2 fuel pipe union bolt (A).

    Torque:
    33 N*m{ 331 kgf*cm , 24 ft.*lbf }

  1. Install 2 new gaskets and the fuel pressure pulsation damper (B).

    Torque:
    33 N*m{ 331 kgf*cm , 24 ft.*lbf }

  1. Install the No. 1 fuel pipe with the bolt (C).

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }



3. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket to the intake air surge tank.



    A109274E04
  1. Using a socket hexagon wrench 8 mm, install the intake air surge tank with the 4 bolts and 2 nuts. Using several steps, tighten the bolts and nuts uniformly in the sequence shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Connect the ground cable connector.



    A109273E05
  1. Install the No. 2 surge tank stay (A) with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Install the No. 1 surge tank stay (B) with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Install the No. 1 engine hunger (C) with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



    A109268
  1. Connect the ventilation hose.



    A106879E02
  1. Connect the fuel vapor feed hose (A).

  1. Connect the No. 3 water by-pass hose (B).

  1. Connect the No. 2 water by-pass hose (C).

  1. Connect the throttle motor connector (D).



4. INSTALL EMISSION CONTROL VALVE SET


    A109272E02
  1. Install the emission control valve set with the 2 nuts (A).

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the No. 2 fuel vapor feed hose (B).

  1. Connect the No. 1 fuel vapor feed hose (C).

  1. Connect the wire harness clamp (D).

  1. Connect the VSV connector (E).



5. INSTALL AIR CLEANER BRACKET


    A108129
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A173493
  1. Align the tab on the throttle body with the groove on the air cleaner hose and tighten the hose clamp.



    A173492
  1. Install the air cleaner case sub-assembly with the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A173491
  1. Connect the intake air flow meter connector.

  1. Connect the 2 wire harness clamps to the air cleaner case.



    A173490
  1. Connect the No. 1 ventilation hose.



7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element to the air cleaner case.



    A175875
  1. Install the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. ADD ENGINE COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 9 ft.*lbf }

  1. Loosen the air drain plug.



    A176032E01
  1. Install a vinyl tube to the vent tube located on the air drain plug.

  1. Fill the radiator with engine coolant until the vinyl tube is filled with the coolant.

  1. Tighten the air drain plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    CAUTION:
    1. Do not use an alcohol type coolant or plain water alone.
    2. The coolant must be mixed with plain water (preferably demineralized water).


    Coolant capacity:

    Condition
    Capacity
    w/ rear heater
    12.8 liters (13.5 US qts, 11.2 lmp.qts)
    w/o rear heater
    10.6 liters (11.2 US qts, 9.3 lmp.qts)

    HINT:
    1. Improper coolants may damage the engine cooling system.
    2. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. Use of coolant which includes more than 50% (freezing protection down to -35°C (-31°F)) or 60% (freezing protection down to -50°C (-58°F)) of ethylene-glycol is recommended but not more than 70%.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Install the radiator cap securely.

  1. Fill the radiator reservoir tank with coolant.

  1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

    HINT:
    The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (C) through (K) and repeat the operation until the coolant level stays at the full level.

  1. Recheck the coolant level inside the radiator reservoir tank. If it is below the full level, add the coolant.



9. INSTALL NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Fit the clips and install the No. 2 engine room side cover LH.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.



10. INSTALL COOL AIR INTAKE DUCT SEAL
  1. Install the cool air intake duct seal with the 11 clips.



11. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175030E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C175029
  1. Engage the 4 clamps.



12. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



14. INSTALL HOOD TO COWL TOP SEAL


    E150148
  1. Engage the 8 clips and install the hood to cowl top seal.



15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



18. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A176028
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and cylinder head.



19. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG) and push the Techstream main switch on.

      NOTICE:
      Do not start the engine.

    3. Select the following menu items: Power train / Engine / Active Test / Control the Fuel Pump Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, hybrid vehicle control ECU and wiring connector.

    5. Check that there are no fuel leaks anywhere on the fuel system after performing maintenance.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the Techstream from the DLC3.