Home › ENGINE › 3MZ-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
(Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



5. REMOVE HOOD TO COWL TOP SEAL


    E150148
  1. Disengage the 8 clips and remove the hood to cowl top seal.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175029
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C175030
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



9. REMOVE COOL AIR INTAKE DUCT SEAL
  1. Remove the 11 clips and cool air intake duct seal.



10. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



11. DRAIN ENGINE COOLANT (for Engine)
  1. Loosen the radiator drain cock plug.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator cap and drain plugs while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

    NOTICE:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plugs.



  1. Remove the radiator cap.


    A176029E01



12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A175875
  1. Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element from the air cleaner case.



13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A173490
  1. Separate the No. 1 ventilation hose.



    A173491
  1. Disconnect the intake air flow meter connector.

  1. Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.



    A173492
  1. Remove the 5 bolts from the air cleaner case sub-assembly.



    A173493
  1. Loosen the hose clamp and separate the No. 1 air cleaner hose.

  1. Remove the air cleaner case sub-assembly.



14. REMOVE AIR CLEANER BRACKET


    A108129
  1. Remove the 2 bolts and air cleaner bracket.



15. REMOVE EMISSION CONTROL VALVE SET


    A109272E01
  1. Disconnect the VSV connector (A).

  1. Remove the wire harness clamp (B).

  1. Disconnect the No. 1 fuel vapor feed hose (C).

  1. Disconnect the No. 2 fuel vapor feed hose (D).

  1. Remove the 2 nuts (E), then remove the emission control valve set.



16. REMOVE INTAKE AIR SURGE TANK


    A106879E03
  1. Disconnect the throttle motor connector (A).

  1. Separate the No. 2 water by-pass hose (B).

  1. Separate the No. 3 water by-pass hose (C).

  1. Separate the fuel vapor feed hose (D).



    A109268
  1. Disconnect the ventilation hose.



    A109273E04
  1. Remove the 2 bolts and No. 1 engine hanger (A).

  1. Remove the 2 bolts and No. 1 surge tank stay (B).

  1. Remove the 2 bolts and No. 2 surge tank stay (C).



    A109274E03
  1. Disconnect the ground cable connector.

  1. Using a socket hexagon wrench 8 mm, remove the 4 bolts.

  1. Remove the 2 nuts, then remove the emission control valve bracket and the intake air surge tank.

  1. Remove the gasket from the intake air surge tank.



17. SEPARATE NO. 1 FUEL PIPE SUB-ASSEMBLY


    A082435E01
  1. Remove the bolt and separate the No. 1 fuel pipe (A).

  1. Remove the fuel pressure pulsation damper and the 2 gaskets (B).

  1. Remove the No. 2 fuel pipe union bolt and the 2 gaskets (C).



18. REMOVE FUEL INJECTOR ASSEMBLY


    A108729
  1. Disconnect the 6 fuel injector connectors.



    A108730
  1. Remove the 4 bolts, and then remove the 2 fuel delivery pipes together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    A108731E01
  1. Remove the 4 No. 1 delivery pipe spacers (A) and the 6 insulators (B) from the intake manifold.



    A081137
  1. Pull out the fuel injectors from the fuel delivery pipes.

  1. Remove the O-rings and grommets from the fuel injectors.