Home › ENGINE › 3MZ-FE INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



5. REMOVE HOOD TO COWL TOP SEAL


    E150148
  1. Disengage the 8 clips and remove the hood to cowl top seal.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175029
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C175030
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



9. REMOVE COOL AIR INTAKE DUCT SEAL
  1. Remove the 11 clips and cool air intake duct seal.



10. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



11. DRAIN ENGINE COOLANT (for Engine)
  1. Loosen the radiator drain cock plug.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator cap and drain plugs while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

    NOTICE:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plugs.



  1. Remove the radiator cap.


    A176029E01



12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A173489
  1. Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element from the air cleaner case sub-assembly.



13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A173490
  1. Separate the No. 1 ventilation hose.



    A173491
  1. Disconnect the intake air flow meter connector.

  1. Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.



    A173492
  1. Remove the 5 bolts from the air cleaner case sub-assembly.



    A173493
  1. Loosen the hose clamp and separate the No. 1 air cleaner hose.

  1. Remove the air cleaner case sub-assembly.



14. REMOVE AIR CLEANER BRACKET


    A108129
  1. Remove the 2 bolts and air cleaner bracket.



15. REMOVE EMISSION CONTROL VALVE SET


    A109272E01
  1. Disconnect the VSV connector (A).

  1. Remove the wire harness clamp (B).

  1. Disconnect the No. 1 fuel vapor feed hose (C).

  1. Disconnect the No. 2 fuel vapor feed hose (D).

  1. Remove the 2 nuts (E), then remove the emission control valve set.



16. REMOVE INTAKE AIR SURGE TANK


    A106879E03
  1. Disconnect the throttle motor connector (A).

  1. Separate the No. 2 water by-pass hose (B).

  1. Separate the No. 3 water by-pass hose (C).

  1. Separate the fuel vapor feed hose (D).



    A109268
  1. Disconnect the ventilation hose.



    A109273E04
  1. Remove the 2 bolts and No. 1 engine hanger (A).

  1. Remove the 2 bolts and No. 1 surge tank stay (B).

  1. Remove the 2 bolts and No. 2 surge tank stay (C).



    A109274E03
  1. Disconnect the ground cable connector.

  1. Using a socket hexagon wrench 8 mm, remove the 4 bolts.

  1. Remove the 2 nuts, then remove the emission control valve bracket and the intake air surge tank.

  1. Remove the gasket from the intake air surge tank.



17. DISCONNECT FUEL PIPE SUB-ASSEMBLY


    A108294E03
  1. Remove the No. 1 EFI fuel pipe clamp.

  1. Pinch the quick connector and then pull out the No. 1 fuel pipe.

    NOTICE:
    1. Remove dirt or foreign objects on the quick connector before this work.
    2. Do not allow any scratches or foreign objects on the connecting surfaces when disconnecting as the fuel hose connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the connecting surfaces by covering them with a vinyl bag after disconnecting the pipe.
    6. If the quick connector and pipe are stuck, push and pull to release them.



18. DISCONNECT INLET HEATER WATER HOSE


    A109571
  1. Disconnect the inlet heater water hose.



19. REMOVE INTAKE MANIFOLD


    A109275
  1. Remove the nut and disconnect the ground cable.



    A108281
  1. Disconnect the 6 fuel injector connectors.



    A108290E03
  1. In order to remove the intake manifold, using several steps, remove the 9 bolts, 2 nuts and 2 washers uniformly in the sequence shown in the illustration.