DTC B1810/53 Short in Driver Side Squib 2nd Step Circuit |
DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit |
DTC B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit |
DTC B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1810/53 |
|
|
| B1811/53 |
|
|
| B1812/53 |
|
|
| B1813/53 |
|
|

| 1.CHECK CONNECTORS |
![]() |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the steering pad, spiral cable and center airbag sensor assembly.
Disconnect the connectors from the steering pad, spiral cable and center airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the spiral cable connector (on the steering pad side) is not damaged.
|
| ||||
| OK | |
| 2.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP) |
![]() |
Connect the instrument panel wire to the center airbag sensor assembly and spiral cable.
Connect SST (resistance 2.1 Ω) to connector E (black connector).
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector E.
Disconnect the instrument panel wire from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - Body ground | power switch on (IG) | Below 1 V |
| z4-2 (D2+) - Body ground | power switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - z4-2 (D2+) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - Body ground | Always | 1 MΩ or higher |
| z4-2 (D2+) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - z4-2 (D2+) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the steering pad and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Disconnect the instrument panel wire from the spiral cable.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-4 (D2+) - Body ground | power switch on (IG) | Below 1 V |
| D15-3 (D2-) - Body ground | power switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-4 (D2+) - D15-3 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-4 (D2+) - Body ground | Always | 1 MΩ or higher |
| D15-3 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D15-4 (D2+) - D15-3 (D2-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK SPIRAL CABLE |
![]() |
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - Body ground | power switch on (IG) | Below 1 V |
| z4-2 (D2+) - Body ground | power switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - z4-2 (D2+) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - Body ground | Always | 1 MΩ or higher |
| z4-2 (D2+) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z4-1 (D2-) - z4-2 (D2+) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||