DTC B1805/52 Short in Front Passenger Side Squib Circuit |
DTC B1806/52 Open in Front Passenger Side Squib Circuit |
DTC B1807/52 Short to GND in Front Passenger Side Squib Circuit |
DTC B1808/52 Short to B+ in Front Passenger Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1805/52 |
|
|
| B1806/52 |
|
|
| B1807/52 |
|
|
| B1808/52 |
|
|

| 1.CHECK CONNECTORS |
![]() |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that connectors are properly connected to the front passenger airbag assembly and center airbag sensor assembly. Also check that the connectors that link the instrument panel wire assembly and instrument panel wire are properly connected.
Disconnect the connectors from the front passenger airbag assembly and center airbag sensor assembly. Also disconnect the instrument panel wire from the instrument panel wire assembly.
Check that the terminals of the connectors are not damaged.
Check that the instrument panel wire assembly connector (on the front passenger airbag assembly side) is not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) |
![]() |
Connect the instrument panel wire to the instrument panel wire assembly and center airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector E (orange connector).
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT |
![]() |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector E.
Disconnect the instrument panel wire from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - Body ground | power switch on (IG) | Below 1 V |
| e2-1 (P-) - Body ground | power switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - e2-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - Body ground | Always | 1 MΩ or higher |
| e2-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - e2-1 (P-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Disconnect the instrument panel wire assembly from the instrument panel wire.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| De1-1 (P+) - Body ground | power switch on (IG) | Below 1 V |
| De1-2 (P-) - Body ground | power switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| De1-1 (P+) - De1-2 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| De1-1 (P+) - Body ground | Always | 1 MΩ or higher |
| De1-2 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| De1-1 (P+) - De1-2 (P-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK INSTRUMENT PANEL WIRE ASSEMBLY |
![]() |
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - Body ground | power switch on (IG) | Below 1 V |
| e2-1 (P-) - Body ground | power switch on (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - e2-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - Body ground | Always | 1 MΩ or higher |
| e2-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e2-2 (P+) - e2-1 (P-) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||