ELECTRONICALLY CONTROLLED BRAKE SYSTEM > INITIALIZATION |
| DESCRIPTION |
Perform initialization and calibration of the linear solenoid valve when the skid control ECU, brake actuator or brake pedal stroke sensor is replaced.
Follow the procedure to perform initialization.
| Part to be Replaced | Necessary Operation |
| Skid control ECU | Initialization and calibration of the linear solenoid valve |
| Brake actuator assembly |
|
|
|
| PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE (When Using the Techstream) |
Clear the stored linear solenoid valve calibration data.
Turn the power switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in P.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Select the skid control ECU to clear the linear solenoid valve calibration data using the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Reset Memory.
Perform initialization and calibration of the linear solenoid valve.
Perform the zero point calibration of yaw rate and acceleration sensor (Click here).
Perform initialization and calibration of the linear solenoid valve.
Turn the power switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in P.
Connect the Techstream to the DLC3.
Turn the power switch on (IG) with the brake pedal released.
Turn the Techstream on.
Switch the skid control ECU to the Test Mode using the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / ECB* Utility / Linear Valve Offset.
*: Electronically Controlled Brake System
Leave the vehicle stationary without depressing the brake pedal for 1 or 2 minutes.
![]() |
Check that the interval between blinks of the brake warning light / yellow (minor malfunction) changes from 1 second to 0.25 seconds.
Check that DTC C1345 (linear solenoid valve offset learning undone) which indicates trouble with stroke sensor zero point learning is not output when the brake warning light / yellow (minor malfunction) changes to the Test Mode display upon initialization and calibration of the linear solenoid valve completion.
Enter the normal mode from the Test Mode following the Techstream directions.
| PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE (When not Using the Techstream) |
Clear the stored linear solenoid valve calibration data.
Turn the power switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in P.
Turn the power switch on (IG) with the brake pedal released.
![]() |
Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
Check that no codes other than ABS code 42, VSC code 45 and electronically controlled brake system code 48, 66, or 95 are stored in the diagnostic system.

Remove SST from the terminals of the DLC3.
Perform initialization and calibration of the linear solenoid valve.
Perform the zero point calibration of yaw rate and acceleration sensor (Click here).
Perform initialization and calibration of the linear solenoid valve.
Turn the power switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in P.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the power switch on (IG) with the brake pedal released.
Leave the vehicle stationary without depressing the brake pedal for 1 or 2 minutes.
![]() |
Check that the interval between blinks of the brake warning light / yellow (minor malfunction) changes from 1 second to 0.25 seconds.
Check that DTC 66 (linear solenoid valve offset learning undone) which indicates trouble with stroke sensor zero point learning is not output when the brake warning light / yellow (minor malfunction) changes to the Test Mode display upon initialization and calibration of the linear solenoid valve completion.
Turn the power switch off and disconnect the SST from the DLC3.